Samsung NE63T8111SS/AA Installation Guide - Page 12

Installing a 4-wire conduit

Get Samsung NE63T8111SS/AA PDF manuals and user guides View all Samsung NE63T8111SS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Connecting the power CAUTION You must check voltage after connecting power cord. Live 1 - Neutral Live 2 - Neutral Live 1 - Live 2 120 V 120 V 208 V / 240 V Installing a 4-wire conduit • Aluminum building wire may be used but it must be rated for the correct amperage and voltage to make the connection. Connect the wires as described below. • The wire you use, the location and enclosure of splices, etc., must conform to good wiring practices and local codes. 1. Loosen the 3 lower terminal screws from the terminal block. Remove the ground screw and ground plate and retain them. 2. Cut and discard the ground strap. Do not discard any screws. 3. Insert the ground bare wire tip between the range frame and the ground plate (removed earlier) and secure it in place with the ground screw (removed earlier). 4. Insert the bare wire (white/neutral) tip through the bottom center of the terminal block opening. 5. Insert the two side bare wire tips into the lower left and the lower right terminal block openings. 6. Tighten the screws until the wire is firmly secured (35 to 50 inch-lbs.). Do not over-tighten the screws since it could damage the wires. 7. Go to Step 5 on page 13 to continue with the installation. Ground strap Live 1 White Black Red Neutral terminal Ground plate Wire tips Live 2 Black White Ground Red wire (Green) CAUTION You must check voltage after connecting power cord. Live 1 - Neutral Live 2 - Neutral Live 1 - Live 2 120 V 120 V 208 V / 240 V Connecting the poCwoenrnecting the power 12 English Install_NE63T8911_AA_DG68-01257A-00_EN.indd 12 2020-03-26 6:27:51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
12 English
Connecting the power
Connecting the power
Connecting the power
CAUTION
You must check voltage after connecting power cord.
Live 1 - Neutral
120 V
Live 2 - Neutral
120 V
Live 1 - Live 2
208 V / 240 V
Installing a 4-wire conduit
•
Aluminum building wire may be used but it must be rated for the correct
amperage and voltage to make the connection. Connect the wires as described
below.
•
The wire you use, the location and enclosure of splices, etc., must conform to
good wiring practices and local codes.
1.
Loosen the 3 lower terminal screws from the terminal block. Remove the
ground screw and ground plate and retain them.
2.
Cut and discard the ground strap. Do not discard any screws.
3.
Insert the ground bare wire tip between the range frame and the ground
plate (removed earlier) and secure it in place with the ground screw (removed
earlier).
4.
Insert the bare wire (white/neutral) tip through the bottom center of the
terminal block opening.
5.
Insert the two side bare wire tips into the lower left and the lower right
terminal block openings.
6.
Tighten the screws until the wire is firmly secured (35 to 50 inch-lbs.). Do not
over-tighten the screws since it could damage the wires.
7.
Go to
Step 5
on page 13 to continue with the installation.
Neutral
terminal
Live 2
Ground
wire (Green)
Wire tips
Ground strap
Ground plate
Black
Black
White
White
Red
Red
Live 1
CAUTION
You must check voltage after connecting power cord.
Live 1 - Neutral
120 V
Live 2 - Neutral
120 V
Live 1 - Live 2
208 V / 240 V
Install_NE63T8911_AA_DG68-01257A-00_EN.indd
12
2020-03-26
°° 6:27:51