Samsung NX58M6850SS/AA Installation Guide - Page 22

Step 7. Assemble the surface burners, CAUTION, Step 6. Level the range

Get Samsung NX58M6850SS/AA PDF manuals and user guides View all Samsung NX58M6850SS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Installation instructions Step 6. Level the range Leveling leg 1. Make sure the range is positioned where you want it. 2. Using a wrench, level the range by turning the front leveling legs in or out as necessary. Counterclockwise shortens the leg and lowers the range. Clockwise lengthens the leg and raises the range. NOTE • Adjusting the two front legs is usually sufficient, but all four legs adjust if necessary. • Adjust the leveling legs only as far as necessary to level the range. Extending the leveling legs more than necessary or removing legs can cause the range to be unstable. 3. If range is next to or between cabinets, make sure the cooktop (without the surface burner grates) is level with the countertops. 4. Position an oven rack in the center rack position. 5. Check the level of the range with a carpenter level using the two positions shown at right. 6. After the range becomes level, slide the range away from the wall so that the anti-tip bracket can be installed. Step 7. Assemble the surface burners CAUTION Do not operate the surface burners without all burner parts in place. 1. Position surface burner heads on top of the surface burner manifolds as shown at right. The electrodes will fit into the slot in the bottom of the heads. Make sure the surface burner heads are flat and parallel with the cooktop. 2. Place the matching size caps on top of each surface burner head. 3. Place the left, center, and right surface burner grates on the cooktop. The edges of the grates should match up with the edges of the cooktop. Installation instructions 22 English Install_NX58M6850SS_DG68-00910A-02_EN+MES+CFR.indb 22 2017-12-13 5:21:57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
22 English
Installation instructions
Installation instructions
Step 7. Assemble the surface burners
CAUTION
Do not operate the surface burners without
all burner parts in place.
1.
Position surface burner heads on top of
the surface burner manifolds as shown
at right. The electrodes will fit into the
slot in the bottom of the heads. Make
sure the surface burner heads are flat
and parallel with the cooktop.
2.
Place the matching size caps on top of
each surface burner head.
3.
Place the left, center, and right surface
burner grates on the cooktop. The
edges of the grates should match up
with the edges of the cooktop.
Step 6. Level the range
Leveling leg
1.
Make sure the range is positioned
where you want it.
2.
Using a wrench, level the range by
turning the front leveling legs in or
out as necessary. Counterclockwise
shortens the leg and lowers the range.
Clockwise lengthens the leg and raises
the range.
NOTE
•
Adjusting the two front legs is usually
sufficient, but all four legs adjust if
necessary.
•
Adjust the leveling legs only as far as
necessary to level the range. Extending
the leveling legs more than necessary
or removing legs can cause the range
to be unstable.
3.
If range is next to or between cabinets,
make sure the cooktop (without the
surface burner grates) is level with the
countertops.
4.
Position an oven rack in the center rack
position.
5.
Check the level of the range with a
carpenter level using the two positions
shown at right.
6.
After the range becomes level, slide the
range away from the wall so that the
anti-tip bracket can be installed.
Install_NX58M6850SS_DG68-00910A-02_EN+MES+CFR.indb
22
2017-12-13
°° 5:21:57