Samsung NX58M6850SS/AA Installation Guide - Page 23

English 23, Roast, START/SET, OFF/CLEAR, Broil, To start the bake burners - lowes

Get Samsung NX58M6850SS/AA PDF manuals and user guides View all Samsung NX58M6850SS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Step 8. Check the ignition of surface burners and oven burners Check the operation of all cooktop and oven burners after the range has been installed and assembled, gas supply lines have been carefully checked for leaks, and electrical power cord has been plugged in. All surface and oven burners have electronic ignition. To turn on a surface burner: 1. Push in and turn the control knob for that surface burner to the LITE position. The "clicking" sound indicates the electronic ignition system is operating properly. The burner will light in about 4 seconds, after the air has been purged from the supply line. 2. After the burner lights, turn the control knob to the desired setting. The "clicking" sound will stop and the flame height will change from Max. to Min. during turning the control knob. 3. Repeat steps 1 and 2 to check the operation of each surface burner in succession. NOTE Place food in the oven after preheating if the recipe calls for it. Preheating is important for good baking results. After the oven has reached the desired cooking temperature, it will beep 6 times. To start the bake burners 03 01 02 04 01 03 04 1. Press the Bake, Roast, or Bake button. 2. If necessary, use the number pad to change the default temperature (350 °F). You can set the oven to any temperature from 175 °F to 550 °F. 3. Press the START/SET button. • The gas oven preheats until it reaches the temperature you set. • When preheating is complete, place the food in the gas oven, and then close the door. 4. When cooking is complete, press the OFF/CLEAR button, and then take out the food. To start the broil burners 03 02 01 03 05 05 1. Put food on a broiling grid in a broiling pan, and then place the pan on the desired rack. 2. Press the Broil pad once for high temperature broiling or twice for low. 3. Press the START/SET pad to start cooking. 4. When on side of the food is browned, turn it over and start cooking the other side. 5. When on both sides is complete, press the OFF/CLEAR pad. Installation instructions Install_NX58M6850SS_DG68-00910A-02_EN+MES+CFR.indb 23 English 23 2017-12-13 5:21:57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
English 23
Installation instructions
To start the bake burners
02
01
01
04
03
04
03
1.
Press the
Bake
,
Roast
, or
Bake
button.
2.
If necessary, use the number pad to change the default temperature (350 °F).
You can set the oven to any temperature from 175 °F to 550 °F.
3.
Press the
START/SET
button.
•
The gas oven preheats until it reaches the temperature you set.
•
When preheating is complete, place the food in the gas oven, and
then close the door.
4.
When cooking is complete, press the
OFF/CLEAR
button, and then take out the
food.
To start the broil burners
01
02
05
03
05
03
1.
Put food on a broiling grid in a broiling pan, and then place the pan on the
desired rack.
2.
Press the
Broil
pad once for high temperature broiling or twice for low.
3.
Press the
START/SET
pad to start cooking.
4.
When on side of the food is browned, turn it over and start cooking the other
side.
5.
When on both sides is complete, press the
OFF/CLEAR
pad.
Step 8. Check the ignition of surface burners and oven burners
Check the operation of all cooktop and oven burners after the range has been
installed and assembled, gas supply lines have been carefully checked for leaks,
and electrical power cord has been plugged in.
All surface and oven burners have electronic ignition.
To turn on a surface burner:
1.
Push in and turn the control knob for
that surface burner to the LITE position.
The "clicking" sound indicates the
electronic ignition system is operating
properly. The burner will light in about
4 seconds, after the air has been
purged from the supply line.
2.
After the burner lights, turn the control
knob to the desired setting. The
"clicking" sound will stop and the flame
height will change from Max. to Min.
during turning the control knob.
3.
Repeat steps 1 and 2 to check the
operation of each surface burner in
succession.
NOTE
Place food in the oven after preheating
if the recipe calls for it. Preheating is
important for good baking results. After
the oven has reached the desired cooking
temperature, it will beep 6 times.
Install_NX58M6850SS_DG68-00910A-02_EN+MES+CFR.indb
23
2017-12-13
°° 5:21:57