Samsung SHR-5082-250 User Manual - Page 14

ASCREW-SPECIAL BWH, 6-32UNC, L10., disk, set the jumper for master and slave.

Get Samsung SHR-5082-250 PDF manuals and user guides
UPC - 836164369079
View all Samsung SHR-5082-250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

3. There are brackets (Bracket-HDD) mounted on the right and left sides where you can mount HDDs. Remove the screws holding each bracket to mount an HDD onto. BRACKETHDD(B) 5. To add a hard disk, the built-in HDD (Primary Master) should have been installed. Basically a built-in HDD has been installed as the Primary Master and a DVD-RW driver as the Secondary Master. Before adding a hard disk, set the jumper for master and slave. The jumper setting method is illustrated on the surface of the purchased hard disk. Fix the hard disk to the Bracket using the (A)SCREW-SPECIAL (BWH, 6-32UNC, L10. 5). Align the 5 spots on the bottom and mounting holes of the Bracket, insert the HDD, and then fix it using the screws. BRACKETHDD(A) 4. If you want to add a hard disk, remove Bracket-HDD(A), power supply cable, signal transmission cable (IDE Cable), and fan cable. BRACKET-HDD(A) SCREW-SPECIAL Screwdriver 10_ installation Screwdriver

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
BRACKET-
HDD(A)
BRACKET-
HDD(B)
BRACKET-HDD(A)
SCREW-SPECIAL
Screwdriver
Screwdriver
10
_ installation
3.
There are brackets (Bracket-HDD) mounted
on the right and left sides where you can
mount HDDs. Remove the screws holding
each bracket to mount an HDD onto.
4.
If you want to add a hard disk, remove
Bracket-HDD(A), power supply cable, signal
transmission cable (IDE Cable), and fan
cable.
5.
To add a hard disk, the built-in HDD (Primary
Master) should have been installed. Basically
a built-in HDD has been installed as the
Primary Master and a DVD-RW driver as the
Secondary Master. Before adding a hard
disk, set the jumper for master and slave.
The jumper setting method is illustrated
on the surface of the purchased hard disk.
Fix the hard disk to the Bracket using the
(A)SCREW-SPECIAL (BWH, 6-32UNC, L10.
5). Align the 5 spots on the bottom and
mounting holes of the Bracket, insert the
HDD, and then fix it using the screws.