Samsung SHR-5082-250 User Manual - Page 17

Bracket using the ASCREW-SPECIAL BWH, 32UNC, L10. 5.

Get Samsung SHR-5082-250 PDF manuals and user guides
UPC - 836164369079
View all Samsung SHR-5082-250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

02 INSTALLATION 5. To add a hard disk, the built-in HDD (Primary Master) should have been installed. Basically a built-in HDD has been installed as the Primary Master. Before adding a hard disk, set the jumper for master and slave. The jumper setting method is illustrated on the surface of the purchased hard disk. Fix the hard disk to the Bracket using the (A)SCREW-SPECIAL (BWH, 6-32UNC, L10. 5). 7. When adding hard disks completes, connect the power supply cable, signal transmission cable (IDE Cable), and fan cable to the hard disks. 8. After checking whether or not the connections have no problem, close the cover. 9. Fix the cover using screws. (Each of left and right sides has 5 spots and the back side has 1 spot.) 6. Re-mount the bracket-HDD mounted with the HDD's to the place where it was separated from. Place the bracket-HDD so that all five mounting spots on the bottom and the bracket-HDD's mounting holes are perfectly aligned, then slide it toward the outside of the product and tighten the screws. installation _13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
02 INSTALLATION
installation _
13
5.
To add a hard disk, the built-in HDD (Primary
Master) should have been installed. Basically a
built-in HDD has been installed as the Primary
Master. Before adding a hard disk, set the
jumper for master and slave. The jumper setting
method is illustrated on the surface of the
purchased hard disk. Fix the hard disk to the
Bracket using the (A)SCREW-SPECIAL (BWH,
6-32UNC, L10. 5).
6.
Re-mount the bracket-HDD mounted with the
HDD’s to the place where it was separated from.
Place the bracket-HDD so that all five mounting
spots on the bottom and the bracket-HDD’s
mounting holes are perfectly aligned, then slide
it toward the outside of the product and tighten
the screws.
7.
When adding hard disks completes, connect the
power supply cable, signal transmission cable
(IDE Cable), and fan cable to the hard disks.
8.
After checking whether or not the connections
have no problem, close the cover.
9.
Fix the cover using screws. (Each of left and right
sides has 5 spots and the back side has 1 spot.)