Samsung WF405ATPASU/AA Trouble Shooting Guide User Manual Ver.1.0 (English, Fr - Page 16

No Water Fill, Tub Full of Suds

Get Samsung WF405ATPASU/AA PDF manuals and user guides View all Samsung WF405ATPASU/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. TROUBLE DIAGNOSIS No Water Fill • Perform Quick Test Mode. Check all of Water Valves visually. (Pre Wash Valve, Cold Water Valve, Bleach Water Valve, Softener dispenses using Cold & Bleach Water Valve, and Hot Water Valve.) • Check if water taps are turned on fully. • Check Water Valves and Water Level Sensor (Refer to PCB Connector Check) • Check if there is any kink in inlet hoses. • Check if inlet screens are clogged up. • Check if water has enough pressure. If so, find out its contributors. • Check if there is any frozen area in the unit (Drain Hose, etc) • Measure the resistance of Water Valve Coil. (It should read 1.18K ohms. Check Pin#1 of CN2 and PIN#1,2,7,8,9 of CN3) • Check Pressure S/W and PCB for loose connections. (Refer to PCB Connector Check.) Tub Full of Suds • Go to "Will Not Drain" and "Will Not Spin" and check the draining. • Check PCB and Drain Pump for any loose wire connection. • Perform Quick Test Mode or Board Output Test to drain. • Use HE (High-Efficiency) or low sudsing detergent specially formulated for front load washers. • Reduce the amount of detergent for that specific load size and soil level. Keep in mind that towel creates more suds generally. • Reduce the amount of detergent when water is soft, or laundry is small or lightly soiled. • Do one more washing cycle with cold water and a table spoon of salt without detergent. 16 WF405ATP-03144A_EN.indd 16 2012-03-02 �� 9:28:50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
16
TROUBLE DIAGNOSIS
No Water Fill
•
Perform Quick Test Mode. Check all of Water Valves visually.
(Pre Wash Valve, Cold Water Valve, Bleach Water
Valve, Softener dispenses using Cold & Bleach Water Valve,
and Hot Water Valve.)
•
Check if water taps are turned on fully.
•
Check Water Valves and Water Level Sensor (Refer to PCB Connector Check)
•
Check if there is any kink in inlet hoses.
•
Check if inlet screens are clogged up.
•
Check if water has enough pressure. If so, find out its contributors.
•
Check if there is any frozen area in the unit (Drain Hose, etc)
•
Measure the resistance of Water Valve Coil.
(It should read 1.18K ohms. Check Pin#1 of CN2 and PIN#1,2,7,8,9 of CN3)
•
Check Pressure S/W and PCB for loose connections. (Refer to PCB Connector Check.)
Tub Full of Suds
•
Go to “Will Not Drain” and “Will Not Spin” and check the draining.
•
Check PCB and Drain Pump for any loose wire connection.
•
Perform Quick Test Mode or Board Output Test to drain.
•
Use HE (High-Efficiency) or low sudsing detergent specially formulated for front load washers.
•
Reduce the amount of detergent for that specific load size and soil level. Keep in mind that towel creates
more suds generally.
•
Reduce the amount of detergent when water is soft, or laundry is small or lightly soiled.
•
Do one more washing cycle with cold water and a table spoon of salt without detergent.
TROUBLE SHOOTING
To avoid risk of electrical shock, personal injury or death; disconnect power to washer
before servicing, unless testing requires power.
WARNING
WF405ATP-03144A_EN.indd
16
2012-03-02
�� 9:28:50