Sanyo PLC-XW200 Owners Manual

Sanyo PLC-XW200 Manual

Get Sanyo PLC-XW200 PDF manuals and user guides View all Sanyo PLC-XW200 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-XW200 manual content summary:

  • Sanyo PLC-XW200 | Owners Manual - Page 1
    Multimedia Projector MODEL PLC-XW200 PLC-XW250 PLC-XW200K PLC-XW250K Network Supported □ Wired LAN 100-Base-TX/10-Base-T Refer to the Owner's Manuals below for details about network function. □ Network Set-up and Operation □ PJ Network Manager Owner's Manual
  • Sanyo PLC-XW200 | Owners Manual - Page 2
    Quick Termination ♦ Colorboard Function The AC power cord can be unplugged immediately At the time of simple projection on the colored wall, after turning off the projector without waiting for the you can get the close color image to the color image termination of the cooling fan rotation (p.20
  • Sanyo PLC-XW200 | Owners Manual - Page 3
    the Filters 59 Resetting the Filter Counter 59 Attaching the Lens Cap 60 Cleaning the Projection Lens 60 Cleaning the Projector Cabinet 60 Lamp Replacement 61 Appendix 63 Troubleshooting 63 Menu Tree 67 Indicators and Projector Condition 69 Compatible Computer Specifications 70
  • Sanyo PLC-XW200 | Owners Manual - Page 4
    the "Troubleshooting" section on pages 63-65 of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
  • Sanyo PLC-XW200 | Owners Manual - Page 5
    on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company. Follow all warnings and instructions marked on the projector. For added protection to the projector during a lightning storm, or when it is left unattended and unused for
  • Sanyo PLC-XW200 | Owners Manual - Page 6
    Improper Installation may reduce the lamp life and cause a fire hazard. 20° Do not tilt the projector more than 20 degrees from side to side. 20° 30° Do not tilt the projector more than 30 degrees from above and below. 30° Do not point the projector up to project an image. Do not point the
  • Sanyo PLC-XW200 | Owners Manual - Page 7
    . Model Number : PLC-XW200, PLC-XW250 Trade Name : Sanyo Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street, Chatsworth, California 91311 Telephone No 818)998-7322 AC Power Cord Requirement The AC Power Cord supplied with this projector meets the
  • Sanyo PLC-XW200 | Owners Manual - Page 8
    60 for attaching.) CAUTION Do not turn on a projector with lens cap attached. High temperature from light beam may damage lens cap and result in fire hazard. ⑧ Air Intake Vent ⑨ Lamp Cover ⑩ Terminals and Connectors ⑪ LAN Connection Terminal ⑫ Power Cord Connector ⑬ Exhaust Vents CAUTION Hot air is
  • Sanyo PLC-XW200 | Owners Manual - Page 9
    and Functions ③ ④ ⑤ ⑥ ⑦ ① CONTROL PORT When the projector is controlled by a computer, connect to this jack with serial control jack (p.15). ⑥ LAN Connection Terminal Connect the LAN cable (refer to the owner's manual of "Network Set-up and Operation"). ⑦ AUDIO IN Connect the audio output
  • Sanyo PLC-XW200 | Owners Manual - Page 10
    Screen Menu (p.21). -Pan the image in the Digital zoom +/- mode Power management mode (p.50). ⑥ MENU button Open or close the On-Screen Menu (p.21). ⑦ LAMP REPLACE indicator Lights yellow when the projection lamp reaches its end of life (pp.61, 69). ⑧ WARNING indicator -Lights red when the projector
  • Sanyo PLC-XW200 | Owners Manual - Page 11
    item. (p.21) - Expand or compress the image in Digital zoom mode. (p.35) ⑳ COMPONENT button Select the COMPONENT input source. (p.37) Note: To ensure safe operation, please observe the following precautions: - Do not bend, drop, or expose the remote control to moisture or heat. - For cleaning
  • Sanyo PLC-XW200 | Owners Manual - Page 12
    an explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions or your local disposal rule or guidelines. Remote Control Operating Range Point the remote control toward the projector (Infrared Remote Receiver) when pressing the buttons. Maximum
  • Sanyo PLC-XW200 | Owners Manual - Page 13
    projector should be set perpendicularly to the plane of the screen. Note: • The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image x 2286 16.1'(4.90m) 19.4'(5.90m) 200" 4064 x 3048 21.5'(6.55m) 25.8(7.87m
  • Sanyo PLC-XW200 | Owners Manual - Page 14
    pin) *(Only one cable is supplied.) • Audio Cables (*One cable is supplied; other cables are not supplied with the projector.) Audio Output Monitor Output Monitor Input MONITOR OUT. Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. 14
  • Sanyo PLC-XW200 | Owners Manual - Page 15
    Audio Cables (Mini Plug: stereo) (Cables are not supplied with the projector. ) External Audio Equipment S-Video Output Audio Output Audio in, the projector's built-in speaker is not available. • See page 72 for ordering optional cables. Unplug the power cords of both the projector and external
  • Sanyo PLC-XW200 | Owners Manual - Page 16
    Component Cable • Component-VGA Cable (Cables are not supplied with this projector.) Audio Output RGB Scart 21-pin Output Component Video Output the projector's built-in speaker is not available. • See page 72 for ordering optional cables. Unplug the power cords of both the projector and
  • Sanyo PLC-XW200 | Owners Manual - Page 17
    be used. If supplied AC power cord does not match your AC outlet, contact your sales dealer. Projector side AC outlet side For the U.S.A. and Canada For Continental Europe For the U.K. Ground To power cord connector on your projector. To the AC outlet. (120 V AC) To the AC outlet. (200 - 240
  • Sanyo PLC-XW200 | Owners Manual - Page 18
    , etc.) before turning on the projector. 2 Connect the projector's AC power cord into an AC outlet. The POWER indicator lights red. Open the lens cap (see pages 8, 60). 3 Press the ON/SYAND-BY button on the top control or on the remote control. The POWER indicator lights green and the cooling fans
  • Sanyo PLC-XW200 | Owners Manual - Page 19
    start to operate the projector. If you entered the projector. What is PIN code projector. Setting a PIN code prevents unauthorized use of the projector operation of the projector with your PIN code. box appeared, the projector will be turned off your PIN code, the projector can no longer be started.
  • Sanyo PLC-XW200 | Owners Manual - Page 20
    the AC power cord to an AC outlet (p.50). • The running speed of cooling fans is changed according to the temperature inside the projector. • Do not put the projector in a case before the projector is cooled enough. • If the WARNING indicator blinks or lights red, see "WARNING indicator" on
  • Sanyo PLC-XW200 | Owners Manual - Page 21
    , which are further divided into other submenus. For each adjustment and setting procedure, refer to respective sections in this manual. 1 Press the MENU button on the top control or the remote control to display the On-Screen Menu. 2 Use the Point ▲▼ buttons to highlight or select a main menu item
  • Sanyo PLC-XW200 | Owners Manual - Page 22
    Display the input source information: Input , H-sync freq., V-sync freq., Screen, Language, Lamp status, Lamp counter , Power management, Key lock, PIN code lock and Remote control (p.57). ⑨ Network See the owner's manual of "Network Set-up and Operation". ⑩ Guide The key operation is displayed. 22
  • Sanyo PLC-XW200 | Owners Manual - Page 23
    after pressing the AUTO SETUP button on the top control or the AUTO SET button on the remote control, correct the image manually as follows: Press the KEYSTONE button on the remote control. The Keystone dialog box appears. Use the Point ▲▼ buttons to correct keystone distortion. The keystone
  • Sanyo PLC-XW200 | Owners Manual - Page 24
    Press the MUTE button on the remote control to select On to temporarily turn off the sound. To turn the sound back on, press the MUTE button again SELECT button to access the selected item. Top Control VOLUME+/buttons Remote Control VOLUME+ button MUTE button VOLUME- button Volume Dialog Box
  • Sanyo PLC-XW200 | Owners Manual - Page 25
    35 for details. LAMP button Press the LAMP button on the remote control to select the lamp mode for changing the brightness on the screen. High Brighter than the Normal mode. Normal....... .Normal brightness Eco Lower brightness reduces the lamp power consumption and extends the lamp life. Note
  • Sanyo PLC-XW200 | Owners Manual - Page 26
    ). To stop the countdown, press the P-TIMER button. To cancel the P-Timer function, press the P-TIMER button again. IMAGE button Press the IMAGE button on the remote control to select a desired image mode of the screen. See pages 32, 39 for details. SCREEN button Select the screen size (See pages 34
  • Sanyo PLC-XW200 | Owners Manual - Page 27
    Input Source Selection (RGB: Computer 1/Computer 2) Direct Operation Choose either Computer 1(RGB) or Computer 2(RGB) by pressing the COMPUTER 1 or Computer 2 button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below
  • Sanyo PLC-XW200 | Owners Manual - Page 28
    PC Adjustment function works to display proper images. If the image is not projected properly, a manual adjustment is required (pp.30-31). There is no signal input from the computer. Check the connection between your computer and the projector. (See "Troubleshooting" on p.63.) The preset system is
  • Sanyo PLC-XW200 | Owners Manual - Page 29
    The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting with the Auto PC Adjustment function. When the image is not provided properly with this operation, manual adjustments are required (pp.30-31). •
  • Sanyo PLC-XW200 | Owners Manual - Page 30
    projector has five independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific Use the Point ◄► buttons to adjust the value, eliminating a flicker from the image displayed (from 0 to 31). Total dots Use the Point ◄► buttons to adjust
  • Sanyo PLC-XW200 | Owners Manual - Page 31
    Computer Input Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select Yes. All adjustments will 1035i or 1080i is selected in the PC System Menu (p.28). • When input computer signal to the projector, PC adjust will become available. 31
  • Sanyo PLC-XW200 | Owners Manual - Page 32
    Mode Selection Direct Operation Select the desired image mode among Dynamic, Standard, Real, Blackboard (Green), Colorboard, Image 1, Image 2, Image 3 and Image 4 by pressing the IMAGE button on the remote control. Remote Control IMAGE button Menu Operation 1 Press the MENU button to display
  • Sanyo PLC-XW200 | Owners Manual - Page 33
    ; press the Point ► button to increase the sharpness of the image (from 0 to 15). Gamma Use the Point ◄► buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15). Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and
  • Sanyo PLC-XW200 | Owners Manual - Page 34
    cannot display any resolution higher than 1600 x 1200. If your computer's screen resolution is higher than it, reset the resolution to the lower before connecting to the projector. • The image data in other than 1024 x 768 is modified to fit the screen size in initial mode. • True, Full, and
  • Sanyo PLC-XW200 | Owners Manual - Page 35
    manually Reset Reset the all adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT button at Yes. For zooming in and out the images image size. The projected image can be also compressed by pressing the D.ZOOM ▼ or the SELECT button on the remote
  • Sanyo PLC-XW200 | Owners Manual - Page 36
    control. Before using these buttons, correct input source should be selected through menu operation as described below. Remote Control VIDEO button Video S-VIDEO button S-video Menu Operation 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select
  • Sanyo PLC-XW200 | Owners Manual - Page 37
    Source Selection (Component, RGB Scart 21-pin) Direct Operation Choose Computer 1(Component) or Computer 1(Scart) by pressing the COMPONENT or the COMPUTER 1 button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below
  • Sanyo PLC-XW200 | Owners Manual - Page 38
    itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N. System
  • Sanyo PLC-XW200 | Owners Manual - Page 39
    image mode among Dynamic, Standard, Cinema, Blackboard (Green), Colorboard, Image 1, Image 2, Image 3 and Image 4 by pressing the IMAGE button on the remote control. Remote colors. Image 1-4 For viewing with the user preset image mode in the Image Adjust Menu (see pages 40-41). This Image memory is
  • Sanyo PLC-XW200 | Owners Manual - Page 40
    button to increase the brightness (from 0 to 63). Image Adjust Menu Reset Store Selected Image mode Color Press the Point ◄ button decrease the , Green or Blue is adjusted, the Color temp. level will change to User. • Tint cannot be selected when the video system is PAL, SECAM, PAL-M or PAL-N
  • Sanyo PLC-XW200 | Owners Manual - Page 41
    function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the then select Yes. Stored data can be called up by selecting an Image (1-4) in the Image Mode Selection on page 39. Note: Noise reduction and Progressive
  • Sanyo PLC-XW200 | Owners Manual - Page 42
    image at the 4:3 normal video aspect ratio. Wide Provide the image at the 16:9 wide screen ratio. Custom Adjust the screen scale and position manually position is used. Reset Reset the all adjusted values. Press the SELECT button at Reset to display a confirmation box. To reset, press the SELECT
  • Sanyo PLC-XW200 | Owners Manual - Page 43
    Setting Setting This projector has a Setting menu that allows you to set up the other various functions described below. 1 Press the MENU button to display the On-Screen Menu.
  • Sanyo PLC-XW200 | Owners Manual - Page 44
    the projector's tilt. Manual . . . Works only when pressing the AUTO SETUP button on the top control or the AUTO SET button on the remote control VIDEO or COMPONENT or S-VIDEO button is pressed, Input search will stop and go back to the button's input signal. • Input search, Auto PC adj. and Auto
  • Sanyo PLC-XW200 | Owners Manual - Page 45
    displays. Use this function when you want to project images after the lamp becomes bright enough. The factory default setting is in this option. Countdown Off....... Show the input image instead of the countdown when turning on the projector. Use this function when you want to project the
  • Sanyo PLC-XW200 | Owners Manual - Page 46
    Logo select and Capture functions cannot be selected. Logo select Logo select This function decides on the starting-up display from among following options. User......... Show the image you captured. Default..... Show the factory-set logo. Off Show the countdown display only. Off Off 46
  • Sanyo PLC-XW200 | Owners Manual - Page 47
    be captured up to XGA (1024 x 768). A signal from video equipment can be captured except for 720p, 1035i, and 1080i. • When capturing the image that has been adjusted by the Keystone function, the adjusted data is automatically reset and the projector captures an image without keystone correction
  • Sanyo PLC-XW200 | Owners Manual - Page 48
    -digit number. After entering the four-digit number, move the pointer to Set. Press the SELECT button so that you can start to operate the projector. If you entered an incorrect Logo PIN code, Logo PIN code and the number will turn red for a moment. Enter the correct Logo PIN code
  • Sanyo PLC-XW200 | Owners Manual - Page 49
    On, the picture will be left/right reversed. This function is used to project the image from rear of the screen. Ceiling Rear Terminal The COMPUTER IN 2/MONITOR OUT terminal on the back of the projector is switchable for computer input or monitor output. (See page 9) Select Computer 2 or Monitor
  • Sanyo PLC-XW200 | Owners Manual - Page 50
    Point ▲▼ buttons to set the Timer(1~30min). Power management Time left before Lamp is off. Note: Factory default is Ready: 5 min. On start When this function is set to On, the projector will be automatically turned on just by connecting the AC power cord to a wall outlet. Note: • When Standby
  • Sanyo PLC-XW200 | Owners Manual - Page 51
    projector is powered off. Eco Select Eco when you do not use the projector via network. The projector's network function will stop when turning off the projector, you can not turn on the projector via network. Refer to the owner's manual of "Network Set-up and Operation". Note: • Factory default
  • Sanyo PLC-XW200 | Owners Manual - Page 52
    the time of power on. Then the projector will turn off after 3 minutes. Lamp replacement icon Lamp life control • The Lamp replacement icon will not appear when the Display function is set to Off (p.45), during Freeze (p.25), or No show (p.26). Remote control This projector provides two
  • Sanyo PLC-XW200 | Owners Manual - Page 53
    Off Unlocked. On1.......... Enter the PIN code every time turning on the projector. On2.......... Enter the PIN code to operate the projector once the power cord is disconnected; as long as the AC power cord is connected, the projector can be operated without a PIN code. Whenever you change the PIN
  • Sanyo PLC-XW200 | Owners Manual - Page 54
    new pin code in column of the pin code no. memo on page 75, and keep it securely. If you forget your PIN code, the projector can no longer be started. 54
  • Sanyo PLC-XW200 | Owners Manual - Page 55
    when using the projector in higher altitudes (about 2,000 meters to 3,000 meters above the sea level) where the fans have lesser cooling effect. Note: The fan noise becomes louder in On1 and On2. Lamp counter Be sure to reset the Lamp replacement counter after the lamp is replaced. (p. 61) Press
  • Sanyo PLC-XW200 | Owners Manual - Page 56
    to set a frequency for the filter cleaning. When the projector reached a specified time between cleanings, a Filter warning icon appears on the screen, notifying the cleaning is necessary. After cleaning the filter, be sure to select Reset and set the timer. The Filter warning icon will not turn off
  • Sanyo PLC-XW200 | Owners Manual - Page 57
    The Information Menu is used for checking the status of the image signal being projected and the operation of the projector. Direct Operation Press the INFO. button on the remote control to display the Information Menu. Remote Control Menu Operation Press the Point ▲▼ buttons to select the
  • Sanyo PLC-XW200 | Owners Manual - Page 58
    ? Clean the filter periodically. The projector is shut down and the WARNING indicator lights red. When the projector detects an abnormal condition, it is automatically shut down to protect the inside of the projector and the WARNING indicator lights red. In this case, unplug the AC power cord and
  • Sanyo PLC-XW200 | Owners Manual - Page 59
    a lens, LCD panels, or optical elements inside the projector degrading the quality of a projected image. When the symptoms above are noticed, contact your authorized dealer or service station for proper cleaning. Note: Please be sure to fit this edge when inserting this filter. Air filter (back
  • Sanyo PLC-XW200 | Owners Manual - Page 60
    the Lens Cap When moving this projector or while not using it over an extended period of time, replace the lens cap. Attach the into the hole on the bottom of the projector and pull at it. Cleaning the Projection Lens Unplug the AC power cord before cleaning. Gently wipe the projection lens with
  • Sanyo PLC-XW200 | Owners Manual - Page 61
    secure the three (3) screws. Make sure that the lamp is set properly. Close the lamp cover and secure the screw. Screw Lamp Handles Screw Screw 5 Connect the AC power cord to the projector and turn on the projector. 6 Reset the lamp replacement counter. See "Lamp Counter" on page 55. Screw 61
  • Sanyo PLC-XW200 | Owners Manual - Page 62
    to the dealer. ● Model No. of your projector ● Replacement Lamp Type No. : PLC-XW200, PLC-XW250 PLC-XW200K, PLC-XW250K : POA-LMP132 (Service Parts No. 610 345 2456) LAMP HANDLING PRECAUTIONS This projector uses a high-pressure lamp which must be handled carefully and properly
  • Sanyo PLC-XW200 | Owners Manual - Page 63
    turned on. -When the projector does not project an image from the connected computer, restart the computer. Problem: - Solutions No power - Plug the power cord of the projector into the AC outlet. - See if the POWER indicator lights red. - Wait until the POWER indicator stops blinking to turn
  • Sanyo PLC-XW200 | Owners Manual - Page 64
    projector. See your computer's instruction manual for the setting. - It takes about 30 seconds to display an image after turning on the projector image cannot be displayed. Press the NO SHOW button or any other button on the remote , 41. Power management does not work. - Power management function
  • Sanyo PLC-XW200 | Owners Manual - Page 65
    Appendix The image is distorted or runs off. - Check PC adjust menu or Screen the Key lock function for the remote control function. See page 53. Indicator blinks or lights. - Check the status of the projector with referring to "Indicators and projector Condition". See page 69. The
  • Sanyo PLC-XW200 | Owners Manual - Page 66
    WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the problem
  • Sanyo PLC-XW200 | Owners Manual - Page 67
    Blackboard (Green) Colorboard Red/Blue/Yellow/Green Image 1 Image 2 Image 3 Image 4 Contrast Brightness Color temp. Red Green Blue Sharpness Gamma Reset Store 0-63 0-63 XLow Low Mid High User 0-63 0-63 0-63 0-15 0-15 Yes/No Image 1 Image 2 Image 3 Image 4 Normal True Wide Full Custom Scale
  • Sanyo PLC-XW200 | Owners Manual - Page 68
    control Lamp counter Key lock Off Projector Remote control PIN code lock Off/On1/On2 PIN code change L1/L2 Off/On1/On2 Lamp counter Hour(s) Filter counter Lamp counter reset Yes/No Filter counter Hour(s) Timer Off/100H/200H/300H Filter counter reset Yes/No Warning log Factory default Yes
  • Sanyo PLC-XW200 | Owners Manual - Page 69
    for projector condition Indicators POWER red/green WARNING red LAMP REPLACE yellow Projector Condition The projector is off. (The AC power cord is unplugged.) Appendix The projector is in stand-by mode. Press the ON/STAND-BY button  to turn on the projector.  The projector is
  • Sanyo PLC-XW200 | Owners Manual - Page 70
    Specifications Basically this projector SVGA 8 SVGA 9 SVGA 10 SVGA 11 MAC 16 MAC 19 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 XGA 10 XGA 11 XGA 12 XGA 13 XGA 14 XGA 15 SXGA 1 SXGA 2 SXGA 3 SXGA 4 RESOLUTION 640 x 480 47.776 60.289 68.633 49.600 41.200 49.702 74.556 74.038 65.290 55.935
  • Sanyo PLC-XW200 | Owners Manual - Page 71
    U.K.) PLC-XW250 / PLC-XW250K: AC 100-120 V (3.5A Max. Ampere), 50/60 Hz (The U.S.A and Canada) AC 200-240 V (1.9A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.) Operating Environment Operating Temperature Storage Temperature 41˚F-95˚F (5 ˚C-35 ˚C) 14˚F-140˚F (-10˚C-60 ˚C) Remote Control
  • Sanyo PLC-XW200 | Owners Manual - Page 72
    Appendix Accessories Owner's Manual (CD-ROM) Quick Reference Guide & Safety Manual AC Power Cord Remote Control and Batteries VGA Cable Lens Cap with String PIN Code Label Network Application (CD-ROM) ● The specifications are subject to change without notice. ● LCD panels are manufactured to the
  • Sanyo PLC-XW200 | Owners Manual - Page 73
    and Information System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. For PJ Link password, see the owner's manual of "Network Set-up and Operation." Projector Input Computer 1 Computer 2 Video RGB
  • Sanyo PLC-XW200 | Owners Manual - Page 74
    /Cr/S-C Input/Output 2 Green/Y/S-Y Input/Output 3 Blue/Cb/--- Input/Output 4 ----- 5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green) 8 Ground (Blue) 9 +5V Power/----10 Ground (Vert.sync.) 11 Ground/----12 DDC Data/----13 Horiz. sync. Input/Output (Composite H/V sync.) 14 Vert. sync. 15
  • Sanyo PLC-XW200 | Owners Manual - Page 75
    in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set No: 4 3 2 1* *Should the four-digit number be
  • Sanyo PLC-XW200 | Owners Manual - Page 76
    Appendix Dimensions 99.5 (3.92) 333.5 (13.13) 247.0 (9.72) 138.0 (5.43) 10 º MAX 90.0 (3.54) 19.0 (0.75) 90.0 (3.54) Unit: mm(inch) Screw Holes for Ceiling Mount Screw: M4 Depth: 10.0(0.39) 217.0 (8.54) 50.0 (1.97) 10.0 (0.39) 51.0 (2.01) 20.0 (0.79) 9.0 (0.35) 85.2 (3.35) 46.0 (1.81)
  • Sanyo PLC-XW200 | Owners Manual - Page 77
    KR5AC SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Multimedia Projector
MODEL
PLC-XW200
PLC-XW250
PLC-XW200K
PLC-XW250K
Owner’s Manual
Network Supported
□
Wired LAN
100-Base-TX/10-Base-T
Refer to the Owner's Manuals below for
details about network function.
□
Network Set-up and Operation
□
PJ Network Manager