Sanyo PLC-XW200 Owners Manual - Page 50

Power management, Ready, Shut down, Timer, No signal, Ready: 5 min, On start, Standby mode, Standby

Get Sanyo PLC-XW200 PDF manuals and user guides View all Sanyo PLC-XW200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Setting Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not operated for a certain period. Select one of the following options: Ready When the lamp has been fully cooled down, the POWER indicator changes to green blinking. In this condition, the projection lamp will be turned on if the input signal is reconnected or any button on the top control or remote control is pressed. Shut down........ When the lamp has been fully cooled down, the power will be turned off. Off Power management function is off. Timer If the input signal is interrupted and no button is pressed for more than 30 seconds, the timer display with No signal appears. It starts the countdown until the lamp is turned off. Use the Point ▲▼ buttons to set the Timer(1~30min). Power management Time left before Lamp is off. Note: Factory default is Ready: 5 min. On start When this function is set to On, the projector will be automatically turned on just by connecting the AC power cord to a wall outlet. Note: • When Standby mode is set to Eco, On start cannot be selected. If you want to set On start to On, Standby mode must be set to Network. • Be sure to turn off the projector properly (see "Turning Off the Projector" on page 20). If the projector is turned off in the incorrect sequence, the On start function will not work properly. 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
50
Setting
Power management
Time left before Lamp is off.
Power management
For reducing power consumption as well as maintaining
the lamp life, the Power management function turns off the
projection lamp when the projector is not operated for a
certain period.
Select one of the following options:
Ready
...............
When the lamp has been fully cooled
down, the POWER indicator changes
to green blinking. In this condition,
the projection lamp will be turned on if
the input signal is reconnected or any
button on the top control or remote
control is pressed.
Shut down
.......
When the lamp has been fully cooled
down, the power will be turned off.
Off
....................
Power management function is off.
Timer
................
If the input signal is interrupted and
no button is pressed for more than
30 seconds, the timer display with
No signal
appears. It starts the
countdown until the lamp is turned off.
Use the Point
▲▼
buttons to set the
Timer(1~30min).
Note:
Factory default is
Ready: 5 min
.
On start
When this function is set to
On
, the projector will be
automatically turned on just by connecting the AC power
cord to a wall outlet.
Note:
• When
Standby mode
is set to
Eco
,
On start
cannot be
selected. If you want to set
On start
to
On
,
Standby
mode
must be set to
Network
.
• Be sure to turn off the projector properly (see “Turning Off
the Projector” on page 20). If the projector is turned off in
the incorrect sequence, the On start function will not
work properly.