Sanyo PLC-XW200 Owners Manual - Page 64

after turning off power°, The setting does not remain

Get Sanyo PLC-XW200 PDF manuals and user guides View all Sanyo PLC-XW200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Appendix No image No sound The color is strange. Some displays are not seen during the operation. Auto PC adjustment function does not work. - Check the connection between your computer or video equipment and the projector. See pages 14-16. - See if the input signal is correctly output from your computer. Some laptop computers may need to change the setting for monitor output when connecting to a projector. See your computer's instruction manual for the setting. - It takes about 30 seconds to display an image after turning on the projector. See page 18. - Check the Input signal, color system, video system or computer system mode. - Make sure the temperature is not out of the specified Operating Temperature (41˚F-95˚F [5˚C-35˚C]). - When No Show is operating, the image cannot be displayed. Press the NO SHOW button or any other button on the remote control. - Check the audio cable connection from audio input source. - Adjust the audio source. - Press the Volume + button. See page 24. - Press the Mute button. See page 24. - When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available. - Is the image projected? You will hear the sound only when the image is projected. - Check the Input signal, color system,video system or computer system mode. - Make sure the Blackboard is not selected on Image select menu. See pages 32, 39. - Check the Display function. See page 45. - Check the Input signal. Auto PC adjustment function can not work when 480p,575p.720p,480i,575i,1035i or 1080i is selected. See page 29 The setting does not remain after turning off power. - Make sure you selected Store after adjusting setting. Some settings can not be stored if not registered with Store. See pages 34, 41. Power management does not work. - Power management function can not work while Freeze or No Show function is running. See page 50. Capture function does not work. - Check the connection and the input signal to see if there is signal. Auto setup does not work properly. - Make sure Off is not selected at any function of Auto setup. See page 44 - Make sure On is not selected at the Ceiling function. See page 49. Auto keystone function does not work even when the projector is tipped. - Make sure the Auto keystone function is not set to Manual. Press the AUTO SETUP button on the top control. See pages 23, 44 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
64
Appendix
No image
– Check the connection between your computer or video equipment
and the projector. See pages 14-16.
– See if the input signal is correctly output from your computer. Some
laptop computers may need to change the setting for monitor output
when connecting to a projector. See your computer’s instruction
manual for the setting.
– It takes about 30 seconds to display an image after turning on the
projector. See page 18.
– Check the Input signal, color system, video system or computer
system mode.
– Make sure the temperature is not out of the specified Operating
Temperature (
41˚F–95˚F [5˚C–35˚C])
.
– When
No Show
is operating, the image cannot be displayed. Press
the NO SHOW button or any other button on the remote control.
No sound
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button. See page 24.
– Press the Mute button. See page 24.
– When the AUDIO OUT is plugged-in, the projector's built-in speaker
is not available.
– Is the image projected? You will hear the sound only when the image
is projected.
The color is strange°
– Check the Input signal, color system,video system or computer
system mode.
– Make sure the
Blackboard
is not selected on Image select
menu. See pages 32, 39.
Some displays are not seen
– Check the Display function. See page 45.
during
the operation°
Auto PC adjustment function
– Check the Input signal. Auto PC adjustment function can not work
does not work°
when
480p
,
575p
.
720p
,
480i
,
575i
,
1035i
or
1080i
is selected. See
page 29.
The setting does not remain
– Make sure you selected
Store
after adjusting setting. Some settings
after turning off power°
can not be stored if not registered with
Store
. See pages 34, 41.
Power management does not
– Power management function can not work while
Freeze
or
No
work°
Show
function is running. See page 50.
Capture function does not work°
– Check the connection and the input signal to see if there is signal.
Auto setup does not work properly°
–
Make sure
Off
is not selected at any function of
Auto setup
. See page
44.
– Make sure
On
is not selected at the Ceiling function. See page 49.
Auto keystone function does not
– Make sure the Auto keystone function is not set to
Manual
. Press
work even when the projector is
the AUTO SETUP button on the top control. See pages 23, 44.
tipped°