Sanyo PLV 80 Owners Manual - Page 40

Ceiling, Lamp control, Power management, On start, Simple menu - plv 80l projector

Get Sanyo PLV 80 - WXGA LCD Projector PDF manuals and user guides
UPC - 086483059254
View all Sanyo PLV 80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

SETTING Ceiling When this function is "On," the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling mounting the projector. Rear When this function is "On," the picture is left/right reversed. This function is used to project the image to a rear projection screen. Simple menu When this function is "On," the value adjustment bar in the picture image adjustment menu is displayed on the bottom left of the screen. Power management For reducing power consumption as well as maintaining the lamp life, the Power Management function turns off the projection lamp when the input signal is interrupted and no button is pressed for 30 seconds or more. If the input signal is interrupted and no button is pressed for 30 seconds or more, the timer display with the message "No signal" appears on the screen. The count-down of the set time will get started. The count-down time can be set between 1 and 30 minutes. When the count-down time has been elapsed, the lamp will be turned off to cool itself down. The READY indicator will be switched off during this cooling-off period. The next operation depends on the setting as follows : Ready . . . . .When the lamp has been fully cooled down, the READY indicator starts flashing. In this condition, the projection lamp will be turned on if the input signal is reconnected or any button on the top control or remote control unit is pressed. Shutdown . . .When the lamp has been fully cooled down, the power will be turned off. Off The Power Management function is canceled. On start When this function is "On," the projector is automatically turned on just by connecting the AC power cord to a wall outlet. NOTE; Be sure to turn the projector off properly (see "Turning Off the Projector" on page 21). If the projector is turned off in the incorrect sequence, such as disconnecting the AC power cord before completing the cool down etc., the On start function does not operate properly. Lamp control This function allows you to change brightness of the screen. ···· brightness according with the input signal. ···· normal brightness. ···· lower brightness reduces the lamp power consumption and extends the lamp life. NOTE; This function available on models PLV-80 and PLV-80L. Ceiling Rear Time left until Lamp off Press the SELECT button at Power management and this box appears. Choose one of three settings with the POINT LEFT/RIGHT buttons, and go to the timer with the POINT DOWN button and set time with the POINT LEFT/RIGHT buttons. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
40
SETTING
Ceiling
Rear
Ceiling
When this function is “On,” the picture is top/bottom and left/right
reversed.
This function is used to project the image from a ceiling
mounting the
projector.
Rear
When this function is “On,” the picture is left/right reversed.
This
function is used to project the image to a rear projection screen.
Lamp control
This function allows you to change brightness of the screen.
····
brightness according with the input signal.
····
normal brightness.
····
lower brightness reduces the lamp power consumption
and extends the lamp life.
Power management
Time left until Lamp off
Press the SELECT button at
Power management and this
box appears.
Choose one of
three settings with the POINT
LEFT/RIGHT buttons, and go
to the timer with the POINT
DOWN button and set time
with the POINT LEFT/RIGHT
buttons.
For reducing power consumption as well as maintaining the lamp
life, the Power Management function turns off the projection lamp
when the input signal is interrupted and no button is pressed for 30
seconds or more.
If the input signal is interrupted and no button is pressed for 30
seconds or more, the timer display with the message "No signal"
appears on the screen. The count-down of the set time will get
started. The count-down time can be set between 1 and 30 min-
utes.
When the count-down time has been elapsed, the lamp will be
turned off to cool itself down. The READY indicator will be
switched off during this cooling-off period. The next operation
depends on the setting as follows :
Ready
. . . . .When the lamp has been fully cooled down, the
READY indicator starts flashing. In this condition,
the projection lamp will be turned on if the input
signal is reconnected or any button on the top
control or remote control unit is pressed.
Shutdown . . .When the lamp has been fully cooled down, the
power will be turned off.
Off
. . . . . . . . .The Power Management function is canceled.
On start
When this function is “On,” the projector is automatically turned on
just by connecting the AC power cord to a wall outlet.
Be sure to turn the projector off properly (see “Turning Off the Projector”
on page 21).
If the projector is turned off in the incorrect sequence, such
as disconnecting the AC power cord before completing the cool down
etc., the On start function does not operate properly.
Simple menu
When this function is “On,” the value adjustment bar in the picture
image adjustment menu is displayed on the bottom left of the
screen.
NOTE;
This function available on models PLV-80 and PLV-80L.
NOTE;