Schwinn 130 Upright Bike 2020 model Assembly and Owners Manual - Page 29

Condition/Problem, Things to Check, Solution

Page 29 highlights

Condition/Problem Resistance does not change (machine turns on and operates) &RQVROHVKXWVRႇ HQWHUV sleep mode) while in use Unit rocks/does not sit level 3HGDOVORRVHXQLWGLႈFXOW to pedal Clicking sound when pedaling Seat post movement Things to Check Check data cable integrity Check data cable connections/orientation Check Servo Motor UHTXLUHVVKURXGUHPRYDO Check Console Check electrical (wall) outlet Check connection at front of unit Check data cable integrity Check data cable connections/orientation Reset machine Check magnet position UHTXLUHVVKURXGUHPRYDO Check Speed Sensor UHTXLUHVVKURXGUHPRYDO Check leveler adjustment Check surface under unit Check pedal to crank arm connection Check pedal to crank arm connection Check locking pin Check adjustment knob Solution All wires in cable should be intact. If any are visibly crimped or cut, replace cable. Be sure cable is connected securely and oriented properly. Reseat all connections. Small latch on connector should line up and snap into place. If magnets move, adjust until they are within the proper range. Replace Servo Motor if not functioning properly. Check for visual sign that Console is damaged. Replace Console if damaged. If the above steps do not resolve the problem, contact Customer Service (if inside US/Canada) or your local distributor (if outside US/Canada) for further assistance. Make sure unit is plugged into a functioning wall outlet. Connection should be secure and undamaged. Replace adapter or connection at unit if either are damaged. All wires in the cable should be intact. If any are cut or crimped, replace cable. Be sure cable is connected securely and oriented properly. Small latch on connector should line up and snap into place. Unplug unit from electrical outlet for 3 minutes. Reconnect to outlet. Magnet should be in place on pulley. Speed sensor should be aligned with magnet and connected to data cable. Realign sensor if necessary. Replace if there is any damage to the sensor or the connecting wire. Adjust levelers until bike is level. $GMXVWPHQWPD\QRWEHDEOHWRFRPSHQVDWHIRUH[WUHPHO\XQeven surfaces. Move bike to level area. Pedal should be tightened securely to crank. Insure connection is not cross-threaded. Remove pedals. Make sure there is no debris on threads, and reinstall the pedals. Be sure adjustment pin is locked into one of the seat post adjustment holes. Be sure knob is securely tightened. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

29
Condition/Problem
Things to Check
Solution
Resistance does not
change (machine turns on
and operates)
Check data cable integrity
All wires in cable should be intact. If any are visibly crimped or
cut, replace cable.
Check data cable
connections/orientation
Be sure cable is connected securely and oriented properly.
Reseat all connections. Small latch on connector should line up
and snap into place.
Check Servo Motor
´UHTXLUHV VKURXG UHPRYDO·
If magnets move, adjust until they are within the proper range.
Replace Servo Motor if not functioning properly.
Check Console
Check for visual sign that Console is damaged. Replace Con-
sole if damaged.
If the above steps do not resolve the problem, contact Cus-
tomer Service (if inside US/Canada) or your local distributor (if
outside US/Canada) for further assistance.
&RQVROH VKXWV Rႇ ´HQWHUV
sleep mode) while in use
Check electrical (wall)
outlet
Make sure unit is plugged into a functioning wall outlet.
Check connection at front
of unit
Connection should be secure and undamaged. Replace
adapter or connection at unit if either are damaged.
Check data cable integrity
All wires in the cable should be intact. If any are cut or crimped,
replace cable.
Check data cable
connections/orientation
Be sure cable is connected securely and oriented properly.
Small latch on connector should line up and snap into place.
Reset machine
Unplug unit from electrical outlet for 3 minutes. Reconnect to
outlet.
Check magnet position
´UHTXLUHV VKURXG UHPRYDO·
Magnet should be in place on pulley.
Check Speed Sensor
´UHTXLUHV VKURXG UHPRYDO·
Speed sensor should be aligned with magnet and connected to
data cable. Realign sensor if necessary. Replace if there is any
damage to the sensor or the connecting wire.
Unit rocks/does not sit
level
Check leveler adjustment
Adjust levelers until bike is level.
Check surface under unit
$GMXVWPHQW PD\ QRW EH DEOH WR FRPSHQVDWH IRU H[WUHPHO\ XQ
-
even surfaces. Move bike to level area.
3HGDOV ORRVHÈXQLW GLႈFXOW
to pedal
Check pedal to crank arm
connection
Pedal should be tightened securely to crank. Insure connection
is not cross-threaded.
Clicking sound when
pedaling
Check pedal to crank arm
connection
Remove pedals. Make sure there is no debris on threads, and
reinstall the pedals.
Seat post movement
Check locking pin
Be sure adjustment pin is locked into one of the seat post
adjustment holes.
Check adjustment knob
Be sure knob is securely tightened.