Seagate ST3000DM001 Barracuda 7200.10 PATA Product Manual - Page 28

Seek time, Start/stop times, Power specifications - benchmark

Get Seagate ST3000DM001 PDF manuals and user guides View all Seagate ST3000DM001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

2.6 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average of all possible single-track seeks in both directions. • Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. *Typical seek times (msec) Track-to-track Average Average latency: Read

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
22
Barracuda 7200.10 PATA Product Manual, Rev. F
2.6
Seek time
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using
drive diagnostics. The specifications in the table below are defined as follows:
•
Track-to-track seek time is an average of all possible single-track seeks in both directions.
•
Average seek time is a true statistical random average of at least 5,000 measurements of seeks between
random tracks, less overhead.
*Measured in quiet mode
Note.
These drives are designed to consistently meet the seek times represented in this manual. Physical seeks,
regardless of mode (such as track-to-track and average), are expected to meet or exceed the noted values.
However, due to the manner in which these drives are formatted, benchmark tests that include command
overhead or measure logical seeks may produce results that vary from these specifications.
2.7
Start/stop times
2.8
Power specifications
The drive receives DC power (+5V or +12V) through a four-pin standard drive power connector.
2.8.1
Power consumption
Power requirements for the drives are listed in the table on page 23. Typical power measurements are based
on an average of drives tested, under nominal conditions, using +5.0V and +12.0V input voltage at 25°C ambi-
ent temperature.
•
Spinup power
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
•
Seek mode
During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does
not execute a read or write operation. Servo electronics are active. Seek mode power represents the worst-
case power consumption, using only random seeks with read or write latency time. This mode is not typical
and is provided for worst-case information.
•
Read/write power and current
Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-msec
delay, then a 16-sector read followed by a 32-msec delay.
•
Operating power and current
Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each
10 reads) and 20 percent drive idle mode.
*Typical seek times (msec)
Read
Write
Track-to-track
<0.8
<1.0
Average
<11.0
<12.0
Average latency:
4.16
4.16
Power-on to Ready (sec)
15 (max)
Standby to Ready (sec)
15 (max)
Ready to spindle stop (sec)
10 (max)