Home » Seagate Manuals » Hard Drives » Seagate ST3000DM001 » Manual Viewer

Seagate ST3000DM001 Barracuda 7200.10 PATA Product Manual - Page 35

Electromagnetic immunity

View all Seagate ST3000DM001 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2.11 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table: Table 11: Radio frequency environments Test Electrostatic discharge Radiated RF immunity Electrical fast transient Surge immunity Conducted RF immunity Voltage dips, interrupts Description Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV 80 to 1,000 MHz, 3 V/m, 80% AM with 1 kHz sine 900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz ± 1 kV on AC mains, ± 0.5 kV on external I/O ± 1 kV differential, ± 2 kV common, AC mains 150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz sine 0% open, 5 seconds 0% short, 5 seconds 40%, 0.10 seconds 70%, 0.01 seconds Performance level B A B B A C C C B Reference standard EN 61000-4-2: 95 EN 61000-4-3: 96 ENV 50204: 95 EN 61000-4-4: 95 EN 61000-4-5: 95 EN 61000-4-6: 97 EN 61000-4-11: 94 Barracuda 7200.10 PATA Product Manual, Rev. F 29

Section	Page
1.0 Introduction	7
2.0 Drive specifications	9
2.1 Specification summary table	9
2.2 Formatted capacity	26
2.2.1 LBA mode	26
2.3 Default logical geometry	26
2.4 Recording and interface technology	27
2.5 Physical characteristics	27
2.6 Seek time	28
2.7 Start/stop times	28
2.8 Power specifications	28
2.8.1 Power consumption	28
2.8.1.1 Typical current profile	30
2.8.2 Conducted noise	30
2.8.3 Voltage tolerance	31
2.8.4 Power management modes	31
2.9 Environmental specifications	32
2.9.1 Ambient temperature	32
2.9.2 Temperature gradient	32
2.9.3 Humidity	32
2.9.3.1 Relative humidity	32
2.9.3.2 Wet bulb temperature	32
2.9.4 Altitude	32
2.9.5 Shock	33
2.9.5.1 Operating shock	33
2.9.5.2 Nonoperating shock	33
2.9.6 Vibration	33
2.9.6.1 Operating vibration	33
2.9.6.2 Nonoperating vibration	33
2.10 Acoustics	34
2.11 Electromagnetic immunity	35
2.12 Reliability	36
2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	36
2.13 Agency certification	36
2.13.1 Safety certification	36
2.13.2 Electromagnetic compatibility	36
2.13.3 FCC verification	37
2.14 Environmental protection	37
2.14.1 European Union Restriction of Hazardous Substances (RoHS)	38
2.15 Corrosive environment	38
3.0 Configuring and mounting the drive	39
3.1 Handling and static discharge precautions	39
3.2 Breather filter hole precautions	40
3.3 Jumper settings	41
3.3.1 Master/slave configuration	41
3.3.2 Cable-select option	41
3.3.3 Ultra ATA/100 cable	42
3.4 Drive mounting	42
4.0 ATA interface	45
4.1 ATA interface signals and connector pins	45
4.1.1 Supported ATA commands	46
4.1.2 Identify Device command	48
4.1.3 Set Features command	51
4.1.4 S.M.A.R.T. commands	52
5.0 Seagate Technology support services	53
A	55
B	55
C	55
D	55
E	55
F	55
G	55
H	55
I	55
J	56
K	56
L	56
M	56
N	56
O	56
P	56
R	56
S	56
T	57
U	57
V	57