Home » Seagate Manuals » Hard Drives » Seagate ST3000DM001 » Manual Viewer

Seagate ST3000DM001 Barracuda 7200.10 PATA Product Manual - Page 30

Typical current profile, Conducted noise, Note.

View all Seagate ST3000DM001 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

2.8.1.1 Typical current profile Figure 1 Typical 5V startup and operation current profile Figure 2 Typical 12V startup and operation current profile 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. • Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected noise at up to 10 MHz. • Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 24 Barracuda 7200.10 PATA Product Manual, Rev. F

Section	Page
1.0 Introduction	7
2.0 Drive specifications	9
2.1 Specification summary table	9
2.2 Formatted capacity	26
2.2.1 LBA mode	26
2.3 Default logical geometry	26
2.4 Recording and interface technology	27
2.5 Physical characteristics	27
2.6 Seek time	28
2.7 Start/stop times	28
2.8 Power specifications	28
2.8.1 Power consumption	28
2.8.1.1 Typical current profile	30
2.8.2 Conducted noise	30
2.8.3 Voltage tolerance	31
2.8.4 Power management modes	31
2.9 Environmental specifications	32
2.9.1 Ambient temperature	32
2.9.2 Temperature gradient	32
2.9.3 Humidity	32
2.9.3.1 Relative humidity	32
2.9.3.2 Wet bulb temperature	32
2.9.4 Altitude	32
2.9.5 Shock	33
2.9.5.1 Operating shock	33
2.9.5.2 Nonoperating shock	33
2.9.6 Vibration	33
2.9.6.1 Operating vibration	33
2.9.6.2 Nonoperating vibration	33
2.10 Acoustics	34
2.11 Electromagnetic immunity	35
2.12 Reliability	36
2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	36
2.13 Agency certification	36
2.13.1 Safety certification	36
2.13.2 Electromagnetic compatibility	36
2.13.3 FCC verification	37
2.14 Environmental protection	37
2.14.1 European Union Restriction of Hazardous Substances (RoHS)	38
2.15 Corrosive environment	38
3.0 Configuring and mounting the drive	39
3.1 Handling and static discharge precautions	39
3.2 Breather filter hole precautions	40
3.3 Jumper settings	41
3.3.1 Master/slave configuration	41
3.3.2 Cable-select option	41
3.3.3 Ultra ATA/100 cable	42
3.4 Drive mounting	42
4.0 ATA interface	45
4.1 ATA interface signals and connector pins	45
4.1.1 Supported ATA commands	46
4.1.2 Identify Device command	48
4.1.3 Set Features command	51
4.1.4 S.M.A.R.T. commands	52
5.0 Seagate Technology support services	53
A	55
B	55
C	55
D	55
E	55
F	55
G	55
H	55
I	55
J	56
K	56
L	56
M	56
N	56
O	56
P	56
R	56
S	56
T	57
U	57
V	57