Sennheiser MX W1 Instructions for Use

Sennheiser MX W1 Manual

Get Sennheiser MX W1 PDF manuals and user guides View all Sennheiser MX W1 manuals
Add to My Manuals
Save this manual to your list of manuals

Sennheiser MX W1 manual content summary:

  • Sennheiser MX W1 | Instructions for Use - Page 1
    digital wireless system MX W1 Instruction manual
  • Sennheiser MX W1 | Instructions for Use - Page 2
    (Pairing) .....9 Setting up your MX W1 for usage 12 Using the MX W1 14 Switching the earphones on/off 14 Switching the transmitter on/off 15 Putting on the earphones 16 Care and maintenance 17 Get the most out of your Sennheiser MX W1 19 Troubleshooting 20 Accessories and spare parts 22
  • Sennheiser MX W1 | Instructions for Use - Page 3
    connected audio device to the minimum before switching the earphones on. Then increase the volume to the lowest comfortable volume. • Use only the Sennheiser supplied MX W1 charging cable and power supply unit. Never use the power supply unit for purposes other than stated in this instruction manual
  • Sennheiser MX W1 | Instructions for Use - Page 4
    Safety instructions for Lithium-Ion rechargeable batteries If abused or misused, rechargeable batteries may leak. In extreme cases, they may even present a • heat hazard • fire hazard • explosion hazard • smoke and gas hazard Please understand that Sennheiser does not accept liability for damage
  • Sennheiser MX W1 | Instructions for Use - Page 5
    MX W1 digital wireless earphone system Thank you for purchasing MX W1 - Sennheiser's completely digital wireless earphone system. We trust that you will enjoy using it and that it will satisfy your expectations. The MX W1 is simple to operate. These instructions for use have been designed to help
  • Sennheiser MX W1 | Instructions for Use - Page 6
    /blue) ¿ Operation/pairing button of the earphone ´ 2.5 mm charging jack ² Battery compartment ´ Transmitter ¶º ¶ Operation/pairing button of the transmitter º Reset button ¾ ¾ LED (orange/blue) µ 2.5 mm charging jack ¸ Connecting cable with ¹ 3.5 mm stereo jack plug ¹ Dowel pin µ ¸ 5
  • Sennheiser MX W1 | Instructions for Use - Page 7
    page 9) Switching the devices on/off (see page 14) Transmitter/earphones: Battery capacity < 5% Putting the MX W1 into operation Charging the MX W1 Charge the rechargeable batteries of all MX W1 devices for 3 hours before first use. When the battery is almost flat, the LEDs » and ¾ flash blue or
  • Sennheiser MX W1 | Instructions for Use - Page 8
    supply unit ƽ. ̈ Connect the charging cable ƾ to the charging jack of: - the transmitter µ and the docking station Ƽ - or the earphones ´. ̈ If you want to charge all devices at one go, insert the earphones into the charging compartments Ƹ of the docking station. ̈ Press the charging button ƻ. 7
  • Sennheiser MX W1 | Instructions for Use - Page 9
    . So it will not drain your audio device's battery. - With a fully charged rechargeable battery, the operating time of the transmitter is approx. 10 hours and of the earphones approx. 3 hours. Charging the earphones on the move When on the move, the earphones can be charged up to three times in
  • Sennheiser MX W1 | Instructions for Use - Page 10
    » and ƺ light up. ̈ Charge the rechargeable batteries until the LEDs go off. Associating the earphones to the transmitter (Pairing) The MX W1 earphones and transmitter are already paired on delivery. To enable wireless transmission, both the earphones and the transmitter have to recognize each other
  • Sennheiser MX W1 | Instructions for Use - Page 11
    0 5s 10s Associating a second pair of earphones to the transmitter With one transmitter you can associate up to two pairs of earphones. If you want to use another pair of earphones, you have to pair your transmitter and the new earphones: ̈ Switch the new earphones off (see page 14). ̈ Switch the
  • Sennheiser MX W1 | Instructions for Use - Page 12
    ̈ Press and hold the operation/pairing button of the trans- mitter until the LED flashes rapidly. 7s ON ON ON After approx. 3 seconds, the new earphones are paired to the transmitter. The LEDs flash blue once every 5 seconds. ON ON ON ̈ Press and hold the operation/pairing button of the
  • Sennheiser MX W1 | Instructions for Use - Page 13
    the earphones to Kleer compatible devices MX W1 is fully compatible to Kleer wireless standard. For pairing the MX W1 with other Kleer compatible devices, please refer to the preceding chapter and to the user manual of your device in question. Setting up your MX W1 for usage Fixing the transmitter
  • Sennheiser MX W1 | Instructions for Use - Page 14
    to an MP3 player or any audio device with a 3.5 mm stereo headphone socket: ̈ Connect the stereo plug of the transmitter ¸ to the 3.5 mm stereo headphone socket of your audio device. Adjusting the earphones to your ears Sennheiser's twist-to-fit system and comfortable earpads allow for the
  • Sennheiser MX W1 | Instructions for Use - Page 15
    the MX W1 To switch the system on, proceed as follows: 1. Switch your audio device on. 2. Switch the earphones on (see following chapter). 3. Switch the transmitter on (see page 15). 4. Put the earphones on (see page 16). You will hear the sound from your sound source. Switching the earphones on
  • Sennheiser MX W1 | Instructions for Use - Page 16
    automatically switch off. - If there is no transmitter in enrollment mode for at least 5 minutes, the earphones automatically switch off. Switching the transmitter on/off ¶ To switch the transmitter on: ̈ Press and hold the transmitter's operation/pairing button ¶ until the LED ¾ flashes
  • Sennheiser MX W1 | Instructions for Use - Page 17
    damage! Listening at high volume levels for long periods can lead to permanent hearing defects. Sennheiser earphones also sound exceptionally good at low volumes. ̈ Set the volume of the audio device to the minimum before switching the earphones on. ̈ Check the R (right) an L (left) marks on the
  • Sennheiser MX W1 | Instructions for Use - Page 18
    , the twist-to-fit pads, earpads and rubber rings should be replaced from time to time. Please order these spare parts from your Sennheiser dealer. ³ ̈ Carefully remove the twist-to-fit pads ³/ rubber rings ƿ/ earpads from the earphones. ̈ Mount the new twist-to-fit pads ³/rubber rings ƿ to the
  • Sennheiser MX W1 | Instructions for Use - Page 19
    caps and slide the caps out of the guide rails. ̈ Insert the new rechargeable batteries as shown. Observe correct polarity when inserting the batteries. ̈ Replace the caps ² and slide them onto the guide rails until it clicks audibly. ̈ Charge the earphones until the corresponding LEDs go off (see
  • Sennheiser MX W1 | Instructions for Use - Page 20
    : optimally, the distance to both earphones should be the same. • other wireless devices operating on similar frequencies (around 2.4 GHz) within your immediate vicinity. In order to optimise the transmission quality of your MX W1, please make sure to: • attach the transmitter at the centre of your
  • Sennheiser MX W1 | Instructions for Use - Page 21
    Troubleshooting Problem No operation indication No sound Sound dropouts Possible cause Possible solution Battery is flat Recharge the battery (see page 6, page 17) Jack plug connection is Check the connection incorrect to your audio device (see page 12) Transmitter or Switch the device on
  • Sennheiser MX W1 | Instructions for Use - Page 22
    audio source Transmitter was switched on before the earphones were switched on Briefly press the transmitter's operation/pairing button ¿ Rechargeable batteries Briefly charge the have just been replaced earphones (see page 18) Resetting the transmitter to the factory settings In case of system
  • Sennheiser MX W1 | Instructions for Use - Page 23
    authorized Sennheiser dealer: Cat. No. Accessory/Spare part 525766 Carrying case 525767 MX W1-C docking station 525768 MX W1-T transmitter 525769 Transmitter straps: 1 elastic fabric strap, 4 rubber bands (2 x S/2 x L) 525770 Lithium-ion rechargeable button cell (2 pieces) for the earphones , 40
  • Sennheiser MX W1 | Instructions for Use - Page 24
    A Output: 5 V DC/0.5 A (x 2) 0 - 40 °C Transmitter Audio connection Charging time of rechargeable battery Power supply Operating time Weight Dimensions 3.5 mm stereo jack socket approx. 2 hrs Input: 5 V DC/120 mA approx. 10 hrs approx. 16 g approx. 40 x 13 x 40 mm Earphones Max. SPL THD Frequency
  • Sennheiser MX W1 | Instructions for Use - Page 25
    approx. 71 x 26 x 74 mm "kleer" wireless technology The MX W1 is based on "kleer" digital wireless transmission technology. • Multiple (stereo) earphones capability • Lossless sound transmission (CD quality) • Smaller size of the devices • Lower battery consumption The Kleer logo is a trademark of
  • Sennheiser MX W1 | Instructions for Use - Page 26
    (DoC) SENNHEISER Model No:MX W1 We, Sennheiser Electronic Corporation Strat. Marketing • Stefanie Reichert One Enterprise Drive • Old Lyme • CT 06371 • USA Tel: +1 if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
  • Sennheiser MX W1 | Instructions for Use - Page 27
    Meet the requirements for: USA: Canada: Europe: FCC ID: IC: DMOMXW1T DMOMXW1R 2099A-MXW1T 2099A-MXW1R Australia & New Zealand: Singapore: Korea: Complies with IDA Standards DB100582 Taiwan: Russia: China: Japan: CMII ID: 2008DJ2183 2008DJ2184 26
  • Sennheiser MX W1 | Instructions for Use - Page 28
    ) 96 Robinson Road, #16-01/04, Singapore 068899 Phone: +65 64116911 Fax: +65 64380476 In EU please contact: Sennheiser electronic GmbH & Co. KG Am Labor 1, 30900 Wedemark, Germany Phone: +49 (5130) 600 0 Fax: +49 (5130) 600 300 www.sennheiser.com ቤ Printed in China Publ. 06/08 528224/A02
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
MX W1
digital wireless system
Instruction manual