Singer S900 INSPIRATION Instruction Manual 2 - Page 7

surface, needle, shank

Get Singer S900 INSPIRATION PDF manuals and user guides View all Singer S900 INSPIRATION manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

6 Fig. 6 SETTING THE NEEDLE See Fig. 6. Raise the needle bar to its highest point, turning wheel toward you by hand. Then loosen the needle clamp screw B and the needle can be inserted into clamp C. Place needle (flat side to right) in the needle clamp and push it upward as far as it will go into the needle clamp hole, tightening the needle clamp screw securely with a screw driver. After changing the needle make one complete revolution of the balance wheel by hand to be sure the needle is in the correct position. Flat surface of needle shank / Fig. 7 THREADING THE BOBBIN CASE Step 1 (illustrated in Fig. 8). Hold bobbin case between thumb and forefinger of left hand, so that the slot in the edge of the bobbin case is on top. Take the bobbin between thumb and forefinger of right hand so that the thread on top leads from left to right. Step 2. Insert bobbin into bobbin case, pull the thread into the slot of the bobbin case as shown in Fig. 9, and draw it under tension spring and into the fork-shaped opening of the spring as shown in Fig. 10.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
SETTING
THE
NEEDLE
See
Fig.
6.
Raise
the
needle
bar
to
its
highest
point,
turning
wheel
toward
you
by
hand.
Then
loosen
the
needle
clamp
screw
B
and
the
needle
can
be
inserted
into
clamp
C.
Place
needle
(flat
side
to
right)
in
the
needle
clamp
and
push
it
upward
as
far
as
it
will
go
into
the
needle
clamp
hole,
tightening
the
needle
clamp
screw
securely
with
a
screw
driver.
After
changing
the
needle
make
one
complete
revolution
of
the
balance
wheel
by
hand
to
be
sure
the
needle
is
in
the
correct
position.
Fig.
7
THREADING
THE
BOBBIN
CASE
Step
1
(illustrated
in
Fig.
8).
Hold
bobbin
case
between
thumb
and
forefinger
of
left
hand,
so
that
the
slot
in
the
edge
of
the
bobbin
case
is
on
top.
Take
the
bobbin
between
thumb
and
forefinger
of
right
hand
so
that
the
thread
on
top
leads
from
left
to
right.
Step
2.
Insert
bobbin
into
bobbin
case,
pull
the
thread
into
the
slot
of
the
bobbin
case
as
shown
in
Fig.
9,
and
draw
it
under
tension
spring
and
into
the
fork-shaped
opening
of
the
spring
as
shown
in
Fig.
10.
6
Fig.
6
Flat
surface
of
needle
shank
/