Sony CSS-HD2 Operating Instructions - Page 13

²-GB, Preparing the Remote Commander

Get Sony CSS-HD2 - Cyber-Shot Station Digital Camera Docking PDF manuals and user guides
UPC - 027242723252
View all Sony CSS-HD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

 The station plate will sink in when it is slid all the way to the correct position. You will hear a click when the plate is attached properly. If the station plate does not sink in properly, evenly push down on its left/right sides.  The positioning marker A on the station plate and positioning marker on the Cyber-shot Station will be aligned. Cyber-shot Station DC plug  Detach the protection cover of the I/O unit.  Before you place a camera on the Cyber-shot Station, be sure to detach the protection cover. Detaching the station plate Hold the Cyber-shot Station with one hand. Hold the camera side guide of the station plate with the other hand and pull the station plate upward. 3 Connect the supplied AC Adaptor to the DC IN jack of the Cyber-shot Station. The POWER lamp of the Cyber-shot Station lights up. AC Adaptor AC Power cord (mains lead) To a wall outlet (wall socket) To use your Cyber-shot Station abroad - Power sources You can use the Cyber-shot Station and the AC Adaptor (supplied) in any country or region where the power supply is within 100 V to 240 V AC 50/60 Hz. Use a commercially available AC plug adaptor, if necessary, depending on the design of the wall outlet (wall socket). AC plug adaptor (not supplied) Do not use an electronic transformer (travel converter), as this may cause a malfunction. Preparing the Remote Commander Notes on the Remote Commander  The Remote Commander is powered by a button type lithium battery (CR2025) installed at the factory. An insulation sheet is inserted to avoid the battery exhaustion. Remove the insulation sheet before using the Remote Commander for the first time. Insulation sheet  Point the remote sensor of the Cyber-shot Station away from strong light sources such as direct sunlight or overhead lightings. Otherwise, the Remote Commander may not function properly. 13-GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
1²-GB
The station plate will sink in when it is slid all
the way to the correct position. You will hear
a click when the plate is attached properly.
If the station plate does not sink in properly,
evenly push down on its left/right sides.
The positioning marker A on the station plate
and positioning marker on the Cyber-shot
Station will be aligned.
Detach the protection cover of the I/O unit.
Before you place a camera on the Cyber-shot
Station, be sure to detach the protection cover.
Detaching the station plate
Hold the Cyber-shot Station with one hand. Hold
the camera side guide of the station plate with the
other hand and pull the station plate upward.
²
Connect the supplied AC Adaptor to the DC 
IN jack of the Cyber-shot Station.
The POWER lamp of the Cyber-shot Station
lights up.
Cyber-shot Station
DC plug
AC Adaptor
To a wall 
outlet  
(wall socket)
AC Power cord 
(mains lead)
To use your Cyber-shot Station abroad  
– Power sources
You can use the Cyber-shot Station and the AC
Adaptor (supplied) in any country or region where
the power supply is within 100 V to 240 V AC
50/60 Hz.
Use a commercially available AC plug adaptor,
if necessary, depending on the design of the wall
outlet (wall socket).
AC plug adaptor
(not supplied)
Do not use an electronic transformer (travel 
converter), as this may cause a malfunction.
Preparing the Remote Commander
Notes on the Remote Commander
The Remote Commander is powered by a button
type lithium battery (CR2025) installed at the
factory. An insulation sheet is inserted to avoid
the battery exhaustion. Remove the insulation
sheet before using the Remote Commander for
the first time.
Insulation sheet
Point the remote sensor of the Cyber-shot Station
away from strong light sources such as direct
sunlight or overhead lightings. Otherwise, the
Remote Commander may not function properly.