Sony KLV-S32A10 Operating Instructions - Page 18

Basic Connections, Cable System or VHF/UHF Antenna System, Cable Box/Digital Cable Box - specifications

Get Sony KLV-S32A10 - Lcd Wega™ Flat Panel Television PDF manuals and user guides View all Sony KLV-S32A10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Connecting the TV Basic Connections Cable System or VHF/UHF Antenna System Cable or VHF only or VHF/UHF 75-ohm coaxial cable Rear of TV VHF/UHF jack From the Channel settings, select Cable On or Cable Off for your type of input signal. A ferrite core is factory attached to the supplied 75-ohm coaxial cable. Do not detach the ferrite core from the coaxial cable. The ferrite core is attached to one end of (not the center of) the supplied 75-ohm coaxial cable. When connecting the cable to the TV, insert the end with the ferrite core into the VHF/UHF jack. Cable Box/Digital Cable Box z The supplied remote control can be programmed to operate your cable box (see "Programming the Remote Control" on page 34). z To change channels using the cable box, set your TV to channel 3 or 4 depending on the cable box channel output. z If you will be controlling all channel selection through your cable box, consider using the Channel Fix feature to set your TV to channel 3 or 4 (see page 53). Use this hookup if: s You subscribe to a cable TV system that uses scrambled or encoded signals requiring a cable box to view all channels, and s You do not intend to hook up any other audio or video equipment to your TV. 1 Connect the coaxial connector from your cable service to the cable box's IN jack. 2 Using the supplied 75-ohm coaxial cable, connect the cable box's OUT jack to the TV's VHF/UHF jack. Cable 75-ohm coaxial cable Rear of TV VHF/UHF jack IN OUT jack jack Cable box Also, set Cable to On in the Channel settings (see page 53). Notes on Using This Connection To Do This ... Do This ... Use the cable box/digital cable Tune the TV to the channel the cable box is set to and then use the cable box to box switch channels. Set up the remote control to Program the remote control. See "Programming the Remote Control" on page 34. operate the cable box/digital cable box Activate the remote control to Press SAT/CABLE (FUNCTION). operate the cable box/digital cable box Control cable box/digital cable See "Operating a Cable Box" on page 36. box functions with the remote control Prevent the accidental switching When using the cable box, you need the TV to stay on the channel the cable box is set of TV channels to. You can use the TV's Channel Fix feature to lock in a specific channel. For details, see "Using the Channel Settings" on page 53. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Connecting the TV
18
Basic Connections
Cable System or
VHF/UHF Antenna
System
Cable or VHF only or VHF/UHF
From the
Channel
settings, select
Cable On
or
Cable Off
for your type of
input signal.
Cable Box/Digital
Cable Box
Use this hookup if:
s
You subscribe to a cable TV system that uses scrambled or encoded
signals requiring a cable box to view all channels, and
s
You do not intend to hook up any other audio or video equipment to
your TV.
1
Connect the coaxial connector from your cable service to the cable
box’s IN jack.
2
Using the supplied 75-ohm coaxial cable, connect the cable box’s OUT
jack to the TV’s VHF/UHF jack.
Also, set
Cable
to
On
in the
Channel
settings (see page 53).
Notes on Using This Connection
A ferrite core is factory attached to the supplied 75-ohm coaxial cable.
Do not detach the ferrite core from the coaxial cable.
The ferrite core is attached to one end of (not the center of) the supplied
75-ohm coaxial cable. When connecting the cable to the TV, insert the
end with the ferrite core into the VHF/UHF jack.
75-ohm coaxial
cable
Rear of TV
VHF/UHF jack
z
The supplied remote
control can be
programmed to operate
your cable box (see
“Programming the Remote
Control” on page 34).
z
To change channels using
the cable box, set your TV
to channel 3 or 4
depending on the cable
box channel output.
z
If you will be controlling all
channel selection through
your cable box, consider
using the Channel Fix
feature to set your TV to
channel 3 or 4 (see page
53).
75-ohm coaxial
cable
Cable
IN
jack
Cable box
OUT
jack
Rear of TV
VHF/UHF jack
To Do This ...
Do This ...
Use the cable box/digital cable
box
Tune the TV to the channel the cable box is set to and then use the cable box to
switch channels.
Set up the remote control to
operate the cable box/digital cable
box
Program the remote control. See “Programming the Remote Control” on page 34.
Activate the remote control to
operate the cable box/digital cable
box
Press
SAT/CABLE
(FUNCTION)
.
Control cable box/digital cable
box functions with the remote
control
See “Operating a Cable Box” on page 36.
Prevent the accidental switching
of TV channels
When using the cable box, you need the TV to stay on the channel the cable box is set
to. You can use the TV’s Channel Fix feature to lock in a specific channel. For
details, see “Using the Channel Settings” on page 53.