Sony RM-VL610N Operating Instructions - Page 33

To clear programmed commands, Assigning Other Components to the Component Select Buttons

Get Sony RM-VL610N - Integrated Remote Commander PDF manuals and user guides View all Sony RM-VL610N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Programming a Series of Commands on the Component Select Buttons (continued) To clear programmed commands 1 Press and while holding SET, press and hold for more than 3 seconds the Component Select button you want to clear. Notes • You can program a Control Program function (Component Macro) for a Component Select button on which the Power-On function (page 27) has been programmed. In this case, the Power-On function is executed when you press the Component Select button, or when you select another component while the consecutive Control Program is being executed. • If the procedure is interrupted the at any point for over more than 20 seconds, the setting mode ends and the series of commands will be programmed up to that point. In this case, clear the program (page 33) and start again from Step 1 to set the entire program from the beginning. You cannot continue programming once the setting mode ends. • If a Component Select button has already "learned" a remote control signal (page 16), you can program a Control Program function (Component Macro), but the function does will not work until you clear the "Learned" Function. To clear the Learning Learned Function, see "Changing or erasing the function of a "learned" button" on page 22. • While you are setting a program, you can insert a 0.4 second interval before the next step is executed by pressing the same Component Select button again. For the example above in the step 2, you can insert a 0.4 second interval between the TV-on signal and the INPUT switching signal at the exercising as the program is executed by pressing the buttons TVtPOWERtTV. Assigning Other Components to the Component Select Buttons You can assign another component to any of the Component Select buttons not being used. Once if you set a Component Select button to a different type of component, the entered component's code number becomes effective. Notes • To use the original component setting, set the component code number again (page 10). • If you enter a new brand's component code number without clearing the previous "learned" functions on that Component Select button, the previously "learned" functions remain effective. Erase the functions you do not use frequently. • You can only assign a TV to the TV Component Select button. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
33
Programming a Series of
Commands on the Component
Select Buttons (continued)
To clear programmed
commands
1
Press and while holding
SET, press and hold for
more than 3 seconds the
Component Select button
you want to clear.
Notes
• You can program a Control Program
function (Component Macro) for a
Component Select button on which
the Power-On function (page 27) has
been programmed. In this case, the
Power-On function is executed when
you press the Component Select
button, or when you select another
component while the consecutive
Control Program is being executed.
• If the procedure is interrupted the at
any point for over more than 20
seconds, the setting mode ends and
the series of commands will be
programmed up to that point. In this
case, clear the program (page 33) and
start again from Step 1 to set the
entire program from the beginning.
You cannot continue programming
once the setting mode ends.
• If a Component Select button has
already “learned” a remote control
signal (page 16), you can program a
Control Program function
(Component Macro), but the function
does will not work until you clear the
“Learned” Function. To clear the
Learning Learned Function, see
“Changing or erasing the function of
a “learned” button” on page 22.
• While you are setting a program, you
can insert a 0.4 second interval before
the next step is executed by pressing
the same Component Select button
again. For the example above in the
step 2, you can insert a 0.4 second
interval between the TV-on signal
and the INPUT switching signal at
the exercising as the program is
executed by pressing the buttons
TV
t
POWER
t
TV.
Assigning Other
Components to the
Component Select
Buttons
You can assign another
component to any of the
Component Select buttons not
being used.
Once if you set a Component
Select button to a different type of
component, the entered
component‘s code number
becomes effective.
Notes
• To use the original component
setting, set the component code
number again (page 10).
• If you enter a new brand‘s
component code number without
clearing the previous “learned”
functions on that Component Select
button, the previously “learned”
functions remain effective. Erase the
functions you do not use frequently.
• You can only assign a TV to the TV
Component Select button.