Sony STR-DB840 Operating Instructions - Page 46

Preset Tuning, Press PRESET TUNING + or PRESET TUNING -

Get Sony STR-DB840 - Fm Stereo/fm-am Receiver PDF manuals and user guides View all Sony STR-DB840 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Preset Tuning For details on the buttons used in this section, see "Brief descriptions of buttons used to receive broadcasts" on page 44. Before tuning to preset stations, be sure to preset them by performing steps on "Presetting radio stations" below. Presetting radio stations 1 Rotate FUNCTION to select the tuner. The last received station is tuned in. 2 Tune in the station that you want to preset using Direct Tuning (page 45) or Automatic Tuning (page 45). 3 Press MEMORY. "MEMORY" appears in the display for a few seconds. Do Steps 4 to 6 before "MEMORY" goes out. 4 Press SHIFT to select a memory page (A, B or C). Each time you press SHIFT, the letter "A," "B" or "C" appears in the display. 5 Press PRESET TUNING + or PRESET TUNING - to select a preset number. If "MEMORY" goes out before you press the preset number, start again from Step 3. 6 Press MEMORY again to store the station. If "MEMORY" goes out before you press the preset number, start again from Step 3. 7 Repeat Steps 2 to 6 to preset another station. To change a preset number to another station Do Steps 1 to 6 to preset the new station to the number. Note If the AC power cord is disconnected for about two weeks, all the preset stations will be cleared from the receiver's memory, and you will have to preset the stations again. Tuning to preset stations You can tune the preset stations either of the following two ways. Scanning the preset stations 1 Rotate FUNCTION to select the tuner. The last received station is tuned in. 2 Press PRESET TUNING + or PRESET TUNING - repeatedly to select the preset station you want. Each time you press the button, the receiver tunes in one preset station at a time, in the corresponding order and direction as follows: nA1˜A2˜...˜A0˜B1˜B2˜...˜B0N nC0˜...C2˜C1N Using the preset codes Use the supplied remote to perform the following operations. For details on the buttons used in this section, see the operating instructions for the supplied remote. 1 Rotate FUNCTION to select the tuner. The last received station is tuned in. 2 For remotes without a display: Press SHIFT to select a memory pare (A, B, or C), then press the preset number of the station you want using the numeric buttons on the supplied remote. For remotes with a display: Select the preset station you want from the list displayed on the supplied remote when TUNER is selected. Receiving Broadcasts 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
46
Receiving Broadcasts
n
A1
˜
A2
˜
...
˜
A0
˜
B1
˜
B2
˜
...
˜
B0
N
n
C0
˜
...C2
˜
C1
N
Tuning to preset stations
You can tune the preset stations either of the following
two ways.
Scanning the preset stations
1
Rotate FUNCTION to select the tuner.
The last received station is tuned in.
2
Press PRESET TUNING + or PRESET TUNING –
repeatedly to select the preset station you want.
Each time you press the button, the receiver tunes in
one preset station at a time, in the corresponding order
and direction as follows:
Using the preset codes
Use the supplied remote to perform the following
operations. For details on the buttons used in this section,
see the operating instructions for the supplied remote.
1
Rotate FUNCTION to select the tuner.
The last received station is tuned in.
2
For remotes without a display:
Press SHIFT to select a memory pare (A, B, or C),
then press the preset number of the station you
want using the numeric buttons on the supplied
remote.
For remotes with a display:
Select the preset station you want from the list
displayed on the supplied remote when TUNER is
selected.
Preset Tuning
For details on the buttons used in this section, see “Brief
descriptions of buttons used to receive broadcasts” on
page 44.
Before tuning to preset stations, be sure to preset them by
performing steps on “Presetting radio stations” below.
Presetting radio stations
1
Rotate FUNCTION to select the tuner.
The last received station is tuned in.
2
Tune in the station that you want to preset using
Direct Tuning (page 45) or Automatic Tuning (page
45).
3
Press MEMORY.
“MEMORY” appears in the display for a few seconds.
Do Steps 4 to 6 before “MEMORY” goes out.
4
Press SHIFT to select a memory page (A, B or C).
Each time you press SHIFT, the letter “A,” “B” or “C”
appears in the display.
5
Press PRESET TUNING + or PRESET TUNING – to
select a preset number.
If “MEMORY” goes out before you press the preset
number, start again from Step 3.
6
Press MEMORY again to store the station.
If “MEMORY” goes out before you press the preset
number, start again from Step 3.
7
Repeat Steps 2 to 6 to preset another station.
To change a preset number to another station
Do Steps 1 to 6 to preset the new station to the number.
Note
If the AC power cord is disconnected for about two weeks, all the
preset stations will be cleared from the receiver’s memory, and
you will have to preset the stations again.