Sony XM-754SX Primary User Manual - Page 2
Stereo Power, Amplifier
View all Sony XM-754SX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Spécifications Circuiterie Circuit OTL (Sortie sans transformateur) Alimentation par impulsions Entrées Prises à broche RCA Sorties Bornes de haut-parleurs Impédance des haut-parleurs 2 - 8 Ω (stéréo) 4 - 8 Ω (utilisé comme amplificateur en pont) Sorties maximales Quatre haut-parleurs : 170 W × 4 (à 4 Ω) Trois haut-parleurs: 170 W × 2 + 400 W × 1 (à 4 Ω) Deux haut-parleurs : 400 W × 2 (à 4 Ω) Sorties nominales (tension d'alimentation de 14,4 V) Quatre haut-parleurs : 75 W × 4 (20 Hz - 20 kHz, 0,04 % THD, à 4 Ω) 100 W × 4 (20 Hz - 20 kHz, 0,1 % THD, à 2 Ω) Deux haut-parleurs : 200 W × 2 (20 Hz - 20 kHz, 0,1 % THD, à 4 Ω) Réponse en fréquence 5 Hz - 50 kHz ( dB) Distorsion harmonique 0,005 % ou inférieure (à 1kHz, 4 Ω) Plage de réglage du niveau d'entrée 0,2 - 6,0 V (prises à broche RCA) 0,4 - 12 V (entrée haut niveau) Filtre passe-haut 50 - 300 Hz, -12 dB/oct Filtre passe-bas 50 - 300 Hz, -12 dB/oct Amplification de basses fréquences 0 - 10 dB (40 Hz) Alimentation Batterie de voiture, courant continu 12 V (masse négative) Tension d'alimentation 10,5 - 16 V Courant à la sortie nominale: 40 A (4Ω) Entrée de télécommande: 1.5 mA Dimensions Env. 358 × 50 × 264 mm (l/h/p) (10 1/2 × 2 × 14 1/8 po.) capuchon de protection de borne compris Poids Env. 3,5 kg (7 li. 11 on.) accessoires non compris Accessoires fournis Vis de montage (4) La conception et les spécifications peuvent être modifiées sans préavis. 3-228-687-11 (1) Stereo Power Amplifier Operating Instructions Mode d'emploi Troubleshooting Guide The following checklist will assist in the correction of most problems which you may encounter with your unit. Before going through the checklist below, refer to the connection and operating procedures. Problem Cause/Solution The POWER indicator does not light up. The fuse is blown. t Replace the fuse with a new one. The ground lead is not securely connected. t Fasten the ground lead securely to a metal point of the car. The voltage going into the remote terminal is too low. • The connected master unit is not turned on. t Turn on the master unit. • The system employs too many amplifiers. t Use a relay. Check the battery voltage (10.5 - 16 V). The OVER CURRENT indicator light up Turn off the power switch. The speaker outputs are short-circuited. t Rectify in red. the cause of the short-circuit. The OFFSET indicator lights up in red. Turn off the power switch. Make sure the speaker cord and ground lead are securely connected. The THERMAL indicator lights up in red. The unit heats up abnormally. • Use speakers with suitable impedance. - 2 - 8 Ω (stereo) , 4 - 8 Ω (when used as a bridging amplifier). • Make sure to place the unit in a well ventilated location. Alternator noise is heard. The power connecting leads are installed too close to the RCA pin cords. t Keep the leads away from the cords. The ground lead is not securely connected. t Fasten the ground lead securely to a metal point of the car. Negative speaker leads are touching the car chassis. t Keep the leads away from the car chassis. The sound is muffled. The sound is too low. The FILTER switch is set to the "LPF" position. The level adjustment control is set to the "MIN" position. Owner's Record The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. XM-754SX Serial No. XM-754SX Sony Corporation 2001 Printed in Korea Guide de dépannage La liste suivante vous aidera à résoudre la plupart des problèmes que vous pouvez rencontrer avec cet appareil. Avant de passer la liste en revue, vérifiez les connexions et les procédures de fonctionnement. Problème Cause/Solution L'indicateur POWER ne s'allume pas. Le fusible est grillé. t Remplacez le fusible par un neuf. Le fil de masse n'est pas connecté correctement. t Fixez correctement le fil de masse à un point métallique de la voiture. La tension entrant à la borne de télécommande est trop faible. • L'appareil maître connecté n'est pas allumé. t Mettez l'appareil maître sous tension. • Le système utilise trop d'amplificateurs. t Utilisez un relais. Vérifiez la tension de la batterie (10,5 - 16 V). L'indicateur OVER CURENT s'allume Coupez l'interrupteur d'alimentation. Les sorties de haut-parleur sont court- en rouge. circuitées. t Remédiez à la cause du court-circuit. L'indicateur OFFSET s'allume en rouge. Coupez l'interrupteur d'alimentation. Assurez-vous que le cordon de hautparleur et le fil de masse sont correctement branchés. L'indicateur THERMAL s'allume en rouge. L'appareil chauffe anormalement. • Utilisez des haut-parleurs d'une impédance appropriée. - 2 - 8 Ω (stéréo) , 4 - 8 Ω (utilisé comme amplificateur en pont). • Installez l'appareil dans un endroit bien aéré. L'alternateur émet un bruit. Les câbles d'alimentation sont installés trop près des câbles à broches RCA. t Eloignez les câbles l'un de l'autre. Le fil de masse n'est pas connecté correctement. t Fixez correctement le fil de masse à un point métallique de la voiture. Les fils négatifs des haut-parleurs touchent la carrosserie de la voiture. t Eloignez les fils de la carrosserie de la voiture. Le son est étouffé. Le commutateur FILTER est mis en position "LPF". Le son est trop faible. La commande de réglage de niveau est mise en position "MIN". Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 75 watts per channel minimum continuous average power into 4 ohms, both channels driven from 20 Hz to 20 kHz with no more than 0.04% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications Circuit system OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Outputs Speaker terminals Speaker impedance 2 - 8 Ω (stereo) 4 - 8 Ω (when used as a bridging amplifier) Maximum outputs Four speakers: 170 W × 4 (at 4 Ω) Three speakers: 170 W × 2 + 400 W × 1 (at 4 Ω) Two speakers: 400 W × 2 (at 4 Ω) Rated outputs (supply voltage at 14.4 V) Four speakers: 75 W × 4 (20 Hz - 20 kHz, 0.04 % THD, at 4 Ω) 100 W × 4 (20 Hz - 20 kHz, 0.1 % THD, at 2 Ω) Two speakers: 200 W × 2 (20 Hz - 20 kHz, 0.1 % THD, at 4 Ω) Frequency response 5 Hz - 50 kHz ( dB) Harmonic distortion 0.005 % or less (at 1kHz, 4 Ω) Input level adjustment range 0.2 - 6.0 V (RCA pin jacks) 0.4 - 12 V (High level input) High-pass filter 50 - 300 Hz, -12 dB/oct Low-pass filter 50 - 300 Hz, -12 dB/oct Low boost 0 - 10 dB (40 Hz) Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.5 - 16 V Current drain at rated output: 40 A (4Ω) Remote input: 1.5 mA Dimensions Approx. 358 × 50 × 264 mm (w/h/d) (10 1/2 × 2 × 14 1/8 in.) not incl. projecting parts and controls Mass Approx. 3.5 kg (7 lb. 11 oz.) not incl. accessories Supplied accessories Mounting screws (4) Design and specifications are subject to change without notice.