Symphonic CSDV840E Owner's Manual - Page 10

Setup Preset for Use Turn on the unit for the first time VCR VCR 1 Turn on the TV and set it to channel 3. • If channel 3 is already occupied for broadcasting, see"RF Output Channel" section. 2 POWER Remote Control TV Screen LANGUAGE SELECT B ENGLISH [ON] or FRANCAIS ESPAÑOL 3 CH 01 AUTO SET UP Do you connect the cable from the cable box or the satellite box to the DVD/VCR's ANT IN jack? YES Yes Press the MENU button to exit • Refer to "Hint for Cable Box or Satellite Box" section on page 6. NO No Please wait for a few minutes. After scanning... • The tuner stops on the lowest memorized channel. • You can select only the channels memorized in this unit by using the CHANNEL buttons. • If "AUTO SET UP" appears on the TV screen again, check the cable connections. Then, press the B button once again. Hint • Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds. To Select a Channel You can select a channel by directly entering channel using the Number buttons on the remote control. Notes for using the Number buttons: • When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.(For example: 117, press 1,1,7) • You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). To Preset the Channel Again 1) Press the MENU button until the main menu appears. 2) Select "CHANNEL SET UP" by pressing the K or L button. Then, press the B button. 3) Select "AUTO SET UP" by pressing the K or L button. Then, press the B button. After scanning, the tuner stops on the lowest memorized channel. To Change the On-Screen Language 1) Press the MENU button until the main menu appears. 2) Select "LANGUAGE SELECT" by pressing the K or L button. Then, press the B button. 3) Select "ENGLISH" , "FRANCAIS" or "ESPAÑOL" by pressing the K or L button. Then, press the CLEAR/C.RESET button. Hint • If you accidentally select Spanish or French and need English: Press the MENU button and choose SELEC. IDIOMA, or SELECTION LANGUE. Press the B button, and select ENGLISH. Finally, press the CLEAR/C.RESET button. Clock Set Up VCR 1 MENU VCR -MENU- TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP B CLOCK SET LANGUAGE SELECT or • If the clock is not set, the CLOCK SET screen appears when you press the MENU button. In this case, go to step [2]. 2 or CLOCK SET MONTH DAY 03 / -- YEAR - - - - HOUR MINUTE AM/PM -- : -- - - Select the current month 3 or CLOCK SET MONTH DAY 03 / 15 YEAR - - - - HOUR MINUTE AM/PM -- : -- - - Select the current day 4 or CLOCK SET MONTH DAY 03 / 15 YEAR 2 0 0 4 HOUR MINUTE AM/PM -- : -- - - Select the current year 5 or CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE AM/PM 05 : -- - - Select the current hour 6 or CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE AM/PM 05 : 40 - - Select the current minute 7 or CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE AM/PM 05 : 40 P M AM B PM Select "AM" or "PM" 8 To exit the CLOCK SET screen. Hint • To go back one step, press the s button (during the steps [2] to [7].) • Your clock setting will be lost if either there is a power failure or this unit has been unplugged for more than 30 seconds. - 10 - EN