TEAC DM-3200 DM-3200 Automation Manual - Page 34

Operation : Automating Library Recall

Page 34 highlights

4 - Operation : Automating Library Recall Automating Library Recall The DM-3200 automation system is capable of including library recall events as part of an automated mix. These are treated by the automation system as Switch Events. All DM-3200 libraries support automated recall: • Snapshot • EQ • Compressor/expanders • Gate • Effects Because there may be differences between control settings recalled by a library and those being played back by the automation system, below are some important things to keep in mind in order to avoid unexpected behavior. The basic rule is that a mix event (library recall or dynamic mix move) only has priority until another mix event (library recall or dynamic mix move) is played back. Writing Library Recall Events Over Existing Static Control Positions When a library recall event is written by the automa- library recall, the control will Revert to its Initial Sta- tion system which affects controls in Static mode, the tus, not its position after the library recall. library recall switch event becomes dynamic mix data. However, the controls themselves remain in Static mode with their Initial Status unaffected. In this case, if a dynamic mix move is written after a If a library is recalled which affects controls in Static mode without the library recall event being written, the controls will update their static positions as they had been directly adjusted. Combining Library Recall With Dynamic Mix Moves Dynamic mix moves are treated in a way similar to will snap to the positions recalled by the library then continuous data by the DM-3200 automation system. snap to reading previous dynamic mix moves as the Library recall events are instantaneous snapshots. If a timecode position crosses the previous data. While library recall occurs while the automation system is this can create some interesting effects when used reading dynamic mix moves, the affected controls purposely, it could take you by surprise. 34 TASCAM DM-3200 Automation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36

4 – Operation : Automating Library Recall
34
TASCAM DM-3200
Automation Guide
Automating Library Recall
The DM-3200 automation system is capable of
including library recall events as part of an auto-
mated mix. These are treated by the automation sys-
tem as Switch Events.
All DM-3200 libraries support automated recall:
• Snapshot
• EQ
• Compressor/expanders
• Gate
• Effects
Because there may be differences between control
settings recalled by a library and those being played
back by the automation system, below are some
important things to keep in mind in order to avoid
unexpected behavior.
The basic rule is that a mix event (library recall or
dynamic mix move) only has priority until another
mix event (library recall or dynamic mix move) is
played back.
Writing Library Recall Events Over Existing Static Control Positions
When a library recall event is written by the automa-
tion system which affects controls in Static mode, the
library recall switch event becomes dynamic mix
data. However, the controls themselves remain in
Static mode with their Initial Status unaffected. In
this case, if a dynamic mix move is written after a
library recall, the control will Revert to its Initial Sta-
tus, not its position after the library recall.
If a library is recalled which affects controls in Static
mode without the library recall event being written,
the controls will update their static positions as they
had been directly adjusted.
Combining Library Recall With Dynamic Mix Moves
Dynamic mix moves are treated in a way similar to
continuous data by the DM-3200 automation system.
Library recall events are instantaneous snapshots. If a
library recall occurs while the automation system is
reading dynamic mix moves, the affected controls
will snap to the positions recalled by the library then
snap to reading previous dynamic mix moves as the
timecode position crosses the previous data. While
this can create some interesting effects when used
purposely, it could take you by surprise.