Toshiba 36AF42 Owners Manual - Page 17

Selecting the Signal Source / Programming Channels into the TV's Memory, To change the signal source

Get Toshiba 36AF42 PDF manuals and user guides View all Toshiba 36AF42 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Welcome to Toshiba Connecting your TV Using the Remote Control Setting up your TV Selecting the signal source Use the TV/VIDEO button on the remote control or TV to select the signal source connected to your TV. To change the signal source: Using the remote control: Press TV/VIDEO on the remote control, and then press the corresponding CHANNEL NUMBER for the desired source (see the illustration below). Using the remote control or TV: Repeatedly press TV-VIDEO until the selected signal source displays in purple. TV Front Panel DEMO MENU TV/VIDEO VOLUME CHANNEL TV/VIDEO CHANNEL z y 0: TV 1: VIDEO 1 2: VIDEO 2 3: VIDEO 3 4: ColorStream To verify the signal source: Press RECALL or press TV/VIDEO on the remote control once. Programming channels into the TV's memory When you press CHANNEL ▲▼ on the TV or remote control, the TV stops only on the channels stored in the TV's memory. Note: To tune the TV to a channel not programmed into the memory, use the CHANNEL NUMBERS on the remote control. Follow the steps below and on the next page to program channels into the TV's memory. Programming channels automatically Your TV can automatically detect all active channels in your area and store them in the TV's memory. After the channels are stored automatically, you can manually add or erase individual channels (see page 18). To program channels automatically: 1. Press MENU. 2. Press x or • to highlight the SET UP menu. 3. Press y or z to highlight TV/CABLE. 4. Press x or • to highlight TV (if you use an antenna) or CABLE (if you use cable). 5. Press z to highlight CH PROGRAM. RECALL MUTE o POWER 1 23 4 56 7 89 CH RTN 100 0 ENT CH VOL MENU/ VOL ENTER TV CABLE VCR CH EXIT FAV CH TV/VIDEO A REC TV/VCR STOP PLAY STILL SOURCE PIP SLOW PAUSE REW FF PIP CH LOCATE SWAP CT-90037 RECALL CHANNEL NUMBERS MENU yz x • CHANNEL yz TV/VIDEO SET UP LANGUAGE: [ENGLISH] FRANCAIS ESPANOL TV/CABLE: [TV] CABLE CH PROGRAM ADD/ERASE: [ADD] ERASE MORE SET UP LANGUAGE: [ENGLISH] FRANCAIS ESPANOL TV/CABLE: [TV] CABLE CH PROGRAM ADD/ERASE: MORE [ADD] ERASE MOVE [ ] SELECT [ ] MOVE [ ] SELECT [ ] 6. Press x or • to start automatic channel programming ("CH PROGRAM" displays on-screen). The TV automatically cycles through every TV or cable channel (depending on which you selected), and stores all active channels in the TV's memory. 7. When automatic channel programming is complete, the message "CH Programming Completed" appears. 8. Press CHANNEL ▲▼ to view the programmed channels. Using the TV's Features Appendix 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
17
W
elcome to
T
oshiba
Connecting
y
our TV
Using the
Remote Control
Setting up
y
our TV
Using the TV’s
F
eatures
Appendix
TV Front Panel
Selecting the signal source
Use the
TV/VIDEO
button on the remote control or TV to select the
signal source connected to your TV.
To change the signal source:
Using the remote control:
Press
TV/VIDEO
on the remote
control, and then press the corresponding
CHANNEL NUMBER
for the desired source (see the illustration below).
Using the remote control or TV:
Repeatedly press
TV-VIDEO
until the selected signal source displays in purple.
0: TV
1: VIDEO 1
2: VIDEO 2
3: VIDEO 3
4: ColorStream
To verify the signal source:
Press
RECALL
or press
TV/VIDEO
on the remote control once.
Programming channels into the TV’s memory
When you press
CHANNEL
▲▼
on the TV or remote control,
the TV stops only on the channels stored in the TV’s memory.
Note:
To tune the TV to a channel not programmed into the memory,
use the
CHANNEL NUMBERS
on the remote control.
Follow the steps below and on the next page to program channels into
the TV’s memory.
Programming channels automatically
Your TV can automatically detect all active channels in your area
and store them in the TV’s memory. After the channels are stored
automatically, you can manually add or erase individual channels
(see page 18).
To program channels automatically:
1. Press
MENU
.
2. Press
x
or
•
to highlight the SET UP menu.
3. Press
y
or
z
to highlight TV/CABLE.
4. Press
x
or
•
to highlight TV (if you use an antenna) or CABLE (if
you use cable).
5. Press
z
to highlight CH PROGRAM.
MOVE
SELECT
[
]
[
]
LANGUAGE:
TV/CABLE:
CH PROGRAM
ADD/ERASE:
MORE
[ENGLISH] FRANCAIS ESPANOL
[TV]
CABLE
[ADD] ERASE
SET UP
MOVE
SELECT
[
]
[
]
LANGUAGE:
TV/CABLE:
CH PROGRAM
ADD/ERASE:
MORE
[ENGLISH] FRANCAIS ESPANOL
[TV] CABLE
[ADD] ERASE
SET UP
6. Press
x
or
•
to start automatic channel programming (“CH
PROGRAM” displays on-screen). The TV automatically cycles
through every TV or cable channel (depending on which you
selected), and stores all active channels in the TV’s memory.
7.
When automatic channel programming is complete, the message
“CH Programming Completed” appears.
8. Press
CHANNEL
▲▼
to view the programmed channels.
MENU
yz
x
•
TV/VIDEO
CHANNEL
yz
CHANNEL
NUMBERS
TV
CABLE
VCR
MENU/
ENTER
CH RTN
RECALL
MUTE
CH
CH
VOL
VOL
1
4
7
2
5
8
3
6
9
0
ENT
100
POWER
o
REW
PAUSE
FF
SOURCE
STILL
PIP
SLOW
PIP CH
LOCATE
SWAP
STOP
PLAY
REC
TV/VCR
TV/VIDEO
FAV CH
A
EXIT
CT-90037
RECALL
DEMO
MENU
TV/VIDEO
VOLUME
CHANNEL
TV/VIDEO
CHANNEL
z
y