Toshiba 36HF71 Owners Manual - Page 13

Programming the remote control for use with a, non-Toshiba VCR or cable TV converter, Cable converter

Page 13 highlights

Introduction Connecting your TV Using the Remote Control Programming the remote control for use with a non-Toshiba VCR or cable TV converter The remote control is pre-programmed to operate Toshiba VCRs. To use the remote control to operate a non-Toshiba VCR or cable converter, follow the steps below to program the remote control. 1. Refer to the "VCR code table" or "Cable TV converter code table" on pages 14-15 to find the corresponding code for your VCR or cable TV converter brand. If more than one code is listed, try each one separately until you find the one that works. 2. If you are reprogramming the remote control to operate your: • VCR: Set the TV/CABLE/VCR switch on the remote control to VCR. • Cable converter: Set the TV/CABLE/VCR switch on the remote control to CABLE. 3. While holding down the RECALL button, press the Number buttons (0-9) to enter the three-digit code for your VCR or cable TV converter. 4. Point the remote control at the VCR or converter and press POWER to test the code. If the VCR or converter responds, you have entered the correct code. If the VCR or converter does not respond, you may have entered the wrong code. Repeat steps 1-4 using another code. 5. Reset the TV/CABLE/VCR switch to TV to control the TV. For future reference, write down the code(s) you used: LIGHT RECALL POWER TV CABLE VCR MUTE TV/VIDEO TIMER 123 CH 456 789 CH RTN VOL 100 0 ENT ADV/ PIP CH RECALL POWER Channel yz Channel Number Enter FAVORITE EXIT PIC SIZE FAV MENU/ ENTER FAV STROBE ADV/ PIP CH STOP SOURCE PLAY PIP REC TV/VCR REW FF Note: • Each timeSTyILLouLOrCeATpElaSWcAeP the batteries, you must reprogram the remote control. • Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled "VCR1/VCR2." If your VCR has this kind of switch, it may not respond to any of the code numbers for your VCR brand name. In this case, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control. VCR code Cable TV converter code Setting up your TV Using the TV's Features Appendix Index 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50

Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV
s
Features
Appendix
Index
13
1
2
3
4
5
6
7
8
9
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
PIC SIZE
EXIT
LIGHT
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
FAVORITE
MENU/
STROBE
ENTER
Programming the remote control for use with a
non-Toshiba VCR or cable TV converter
The remote control is pre-programmed to operate Toshiba VCRs. To
use the remote control to operate a non-Toshiba VCR or cable
converter, follow the steps below to program the remote control.
1. Refer to the
VCR code table
or
Cable TV converter code
table
on pages 14-15 to find the corresponding code for your
VCR or cable TV converter brand.
If more than one code is listed, try each one separately until you
find the one that works.
2. If you are reprogramming the remote control to operate your:
VCR:
Set the TV/CABLE/VCR switch on the remote control
to VCR.
Cable converter:
Set the TV/CABLE/VCR switch on the
remote control to CABLE.
3. While holding down the RECALL button, press the Number
buttons (0-9) to enter the three-digit code for your VCR or cable
TV converter.
4. Point the remote control at the VCR or converter and press
POWER to test the code.
If the VCR or converter responds, you have entered the correct
code.
If the VCR or converter does not respond, you may have entered
the wrong code. Repeat steps 1-4 using another code.
5. Reset the TV/CABLE/VCR switch to TV to control the TV.
For future reference, write down the code(s) you used:
VCR code ________________________________
Cable TV converter code ____________________
Note:
Each time you replace the batteries, you
must reprogram the remote control.
Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled
VCR1/VCR2.
If your VCR has this kind of switch, it may
not respond to any of the code numbers for
your VCR brand name. In this case, set the
switch to the other position (VCR1 or
VCR2) and reprogram the remote control.
POWER
Channel
yz
Channel
Number
Enter
RECALL