Tripp Lite 5PX1000RTNG2 Owners Manual for 5PX1000RTG2 5PX1000RTNG2 5PX1500RTG2 - Page 18

LCD description, In AVR mode

Get Tripp Lite 5PX1000RTNG2 PDF manuals and user guides View all Tripp Lite 5PX1000RTNG2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

4.2 LCD description ① Load status and measurements ② Equipment status icon ③ Status / Message ④ Battery status As default, or after 5 minutes of inactivity, the LCD displays the screen saver. The backlight LCD automatically dims after 5 minutes of inactivity. Press any button to restore the screen. Note. If other indicator appears, see troubleshooting page for additional information. The following table describes the status information provided by the UPS : Operation status Possible cause Action Standby mode The UPS is OFF, waiting for start-up command from user Equipment is not power until button is pressed during start up and the green "normal mode" LED indicator is illuminated. Normal mode The UPS is operating normally. The UPS is powering and protecting the equipment. In AVR mode No beep The UPS is operating normally but the utility voltage is outside Normal mode thresholds. The UPS is powering the equipment through the Automatic Voltage Regulation device. The equipment is still normally protected. On Battery One beep every 10 seconds A utility failure has occurred and the UPS is in Battery mode. The UPS is powering the equipment with battery power. Prepare your equipment for shutdown. End of backup time 1 beep every 3 seconds The UPS is in Battery mode and the battery is running low. This warning is approximate, and the actual time to shutdown may vary significantly. Depending on the UPS Load, the "Battery Low" warning may occur before the battery reaches 20% capacity remaining. 614-40095-00 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
614-40095-00
18
4.2 LCD description
①
Load status and measurements
②
Equipment status icon
③
Status / Message
④
Battery status
As default, or after 5 minutes of inactivity, the LCD displays the screen saver.
The backlight LCD automatically dims after 5 minutes of inactivity. Press any button to restore the screen.
Note. If other indicator appears, see troubleshooting page for additional information.
The following table describes the status information provided by the UPS :
Operation status
Possible cause
Action
Standby mode
The UPS is OFF, waiting for start-up
command from user
Equipment is not power until button
is pressed
during start up and the green "normal mode" LED
indicator is illuminated.
Normal mode
The UPS is operating normally.
The UPS is powering and protecting the equipment.
In AVR mode
No beep
The UPS is operating normally but the
utility voltage is outside Normal mode
thresholds.
The UPS is powering the equipment through the
A
utomatic
V
oltage
R
egulation device. The equipment is
still normally protected.
On Battery
One beep every 10
seconds
A utility failure has occurred and the
UPS is in Battery mode.
The UPS is powering the equipment with battery
power. Prepare your equipment for shutdown.
End of backup time
1 beep every 3
seconds
The UPS is in Battery mode and the
battery is running low.
This warning is approximate, and the actual time to
shutdown may vary significantly. Depending on the
UPS Load, the "Battery Low" warning may occur before
the battery reaches 20% capacity remaining.