Uniden D1688 English Owners Manual - Page 22

Installing a Line Filter or DSL Filter, Liquid Damage, Resetting Stations, Registering Handsets - 2 corded and cordless phone

Get Uniden D1688 PDF manuals and user guides
UPC - 050633273449
View all Uniden D1688 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Installing a Line Filter or DSL Filter A telephone line filter or DSL filter prevents services that use the phone line from causing interference on your phone. To get a line filter, contact your service provider or look in an electronics store. Plug the filter into the telephone wall jack and plug the base into the filter. Make a test call to make sure the noise is gone. Liquid Damage CAUTION: If the base is covered in liquid, disconnect the adapter and phone cord from the wall before touching it. If the liquid is only on the exterior housing of the base or handset, wipe it off and use as normal. If you can hear liquid inside the housing: ♦♦Remove all compartment covers, and disconnect all cables and cords. ♦♦If liquid is leaking from any vent or hole, turn the phone so that vent faces down. If not, place the largest vent face down. ♦♦Let dry for at least 3 days. Check for liquid inside the phone before replacing compartment covers & reconnecting cords. Resetting Stations If you have problems with the base, unplug the base to reset it. Plug it back in after at least a minute. If you have trouble with a cordless handset or if you want to replace one, reset it: 1. Press & hold END and # at the same time until System Reset displays. 2. If you still have the base the handset is registered to, select Deregister HS, then select the handset you want to reset. If you don't have that base anymore, select Base Unavailable. 3. To confirm, select Yes. The handset displays Handset not registered. Registering Handsets If you see a "not registered" message on a handset, you must register it to a base before using it. 1. On the base, open the menu and select Register Accy. 2. On the handset, press and hold #; the handset display says Registering. 3. Wait until the handset display says Registration Complete (about 30 seconds), then pick up the handset and press TALK/FLASH. 4. If you don't hear a dial tone or the handset display says Registration Failed, charge the battery completely, then try again. English - 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
English - 22
Installing a Line Filter or DSL Filter
A telephone line filter or DSL filter prevents services that use the phone
line from causing interference on your phone. To get a line filter, contact
your service provider or look in an electronics store.
Plug the filter into the telephone wall jack and plug the base into the filter.
Make a test call to make sure the noise is gone.
Liquid Damage
CAUTION: If the base is covered in liquid, disconnect the adapter and phone cord
from the wall before touching it.
If the liquid is only on the exterior housing of the base or handset, wipe it
off and use as normal. If you can hear liquid inside the housing:
♦
Remove all compartment covers, and disconnect all cables and cords.
♦
If liquid is leaking from any vent or hole, turn the phone so that vent
faces down. If not, place the largest vent face down.
♦
Let dry for at least 3 days. Check for liquid inside the phone before
replacing compartment covers & reconnecting cords.
Resetting Stations
If you have problems with the base, unplug the base to reset it. Plug it back
in after at least a minute.
If you have trouble with a cordless handset or if you want to replace one,
reset it:
1. Press & hold
END
and
#
at the same time until
System Reset
displays.
2. If you still have the base the handset is registered to, select
Deregister
HS
, then select the handset you want to reset. If you don’t have that base
anymore, select
Base Unavailable
.
3. To confirm, select
Yes
. The handset displays
Handset not registered
.
Registering Handsets
If you see a “not registered” message on a handset, you must register it to a
base before using it.
1. On the base, open the menu and select
Register Accy.
2. On the handset, press and hold
#
; the handset display says
Registering
.
3. Wait until the
handset display says
Registration Complete
(about 30
seconds), then pick up the handset and press
TALK/FLASH
.
4. If you don’t hear a dial tone or the handset display says
Registration
Failed
, charge the battery completely, then try again.