ViewSonic PJ759 User Guide - Page 17

Connecting power supply, Using the security bar and slot

Get ViewSonic PJ759 - 63 Tft LCD Projector PDF manuals and user guides
UPC - 766907274615
View all ViewSonic PJ759 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Setting up Connecting power supply At first, make sure that the power switch of the projector is set to OFF position (marked "O"). 1. Put the connector of the power cord into the AC inlet of the projector. 2. Firmly plug the power cord's plug into the outlet. AC inlet Power cord WARNING ►Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in fire and/or electrical shock. • Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one. • Only plug the power cord into an outlet rated for use with the power cord's specified voltage range. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation. • Never modify the power cord. Using the security bar and slot A commercial anti-theft chain or wire up to 10 mm in diameter can be attached to the security bar on the projector. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool. WARNING ►Do not use the security bar and slot to prevent the projector from falling down, since it is not designed for it. CAUTION ►Do not place anti-theft chain or wire near the exhaust vents. It may become too hot. NOTE • The security bar and slot is not comprehensive theft prevention measures. It is intended to be used as supplemental theft prevention measure. ViewSonic 12 PJ758/PJ759/PJ760

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
ViewSonic
12
PJ758/PJ759/PJ760
Setting up
Connecting power supply
At
fi
rst, make sure that the power switch of the
projector is set to OFF position (marked "O").
1.
Put the connector of the power cord into
the AC inlet of the projector.
2.
Firmly plug the power cord’s plug into the
outlet.
WARNING
►
Please use extra caution when connecting the power cord, as
incorrect or faulty connections may result in
fi
re and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact
your dealer to newly get correct one.
• Only plug the power cord into an outlet rated for use with the power cord's
speci
fi
ed voltage range. The power outlet should be close to the projector and
easily accessible. Remove the power cord for complete separation.
• Never modify the power cord.
Using the security bar and slot
A commercial anti-theft chain or wire up to
10 mm in diameter can be attached to the
security bar on the projector.
Also this product has the security slot for the
Kensington lock.
For details, see the manual of the security
tool.
WARNING
►
Do not use the security bar and slot to prevent the projector
from falling down, since it is not designed for it.
CAUTION
►
Do not place anti-theft chain or wire near the exhaust vents. It
may become too hot.
NOTE
• The security bar and slot is not comprehensive theft prevention
measures. It is intended to be used as supplemental theft prevention measure.
AC inlet
Power cord