ViewSonic X2000B-4K - 4K UHD Ultra Short Throw Laser Projector with 2000 Lumens - Page 14

Page 14 highlights

Remote Control - Receiver Range To ensure proper function of the remote control follow the steps below: 1. The remote control must be held at an angle within 30° perpendicular to the projector's IR remote control sensor(s). 2. The distance between the remote control and the sensor(s) should not exceed 8 m (26 ft.) Approx. 30° NOTE: Refer to the illustration for the location of the infrared (IR) remote control sensor(s). Remote Control - Replacing the Batteries 1. Remove the battery cover from the bottom of the remote control by pressing the finger grip and sliding it across. 2. Remove any existing batteries (if necessary) and install two AAA batteries. NOTE: Observe the battery's polarities as indicated. 3. Replace the battery cover by aligning it with the base and pushing it back into position. NOTE: • Avoid leaving the remote control and batteries in excessive heat or a humid environment. • Replace only with the same or equivalent type recommended by the battery manufacturer. • If the batteries are drained or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control. • Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
14
Remote Control - Receiver Range
To ensure proper func°on of the remote
control follow the steps below:
1.
The remote control must be held at
an angle within 30° perpendicular
to the projector’s IR remote control
sensor(s).
2.
The distance between the remote
control and the sensor(s) should not
exceed 8 m (26 ſt.)
NOTE:
Refer to the illustra°on for
the loca°on of the infrared
(IR) remote control sensor(s).
Approx.
30°
Remote Control - Replacing the Ba±eries
1.
Remove the ba±ery cover from the bo±om of the remote control by pressing the
finger grip and sliding it across.
2.
Remove any exis°ng ba±eries (if necessary) and install two AAA ba±eries.
NOTE:
Observe the ba±ery’s polari°es as indicated.
3.
Replace the ba±ery cover by aligning it with the base and pushing it back into
posi°on.
NOTE:
•
Avoid leaving the remote control and ba±eries in excessive heat or a humid
environment.
•
Replace only with the same or equivalent type recommended by the
ba±ery manufacturer.
•
If the ba±eries are drained or if you will not be using the remote control for
an extended period of °me, remove the ba±eries to avoid damage to the
remote control.
•
Dispose of the used ba±eries according to the manufacturer’s instruc°ons
and local environment regula°ons for your region.