Vtech DS4121-4 User Manual (DS4121-3 User Manual) - Page 32

Set telephone base ringer, Set remote access code, Set message alert tone

Page 32 highlights

Advanced operation Answering system operation Set telephone base ringer This feature allows you to select the telephone base ringer volume levels. You can choose from HI (high), OF (off) or LO (low). To change the setting: 1. Press SET UP in idle mode until the system announces the telephone base ringer setting. 2. Press /SKIP or /REPEAT until the system announces the desired telephone base ringer volume level, then press SET UP to save the setting and go to the next setting or press /PLAY/STOP to save and exit set up mode. • The answering system must be turned on for the message alert tone to function. Set remote access code A two-digit security code is required to access the answering system remotely from any touch tone telephone. The code preset at the factory is 19. You can set the code from 10 to 99. To set the remote access code: 1. Press SET UP when in idle mode until the system announces the remote access code setting. 2. Press /SKIP or /REPEAT to change the remote access code by one, or press and hold /SKIP or /REPEAT to change it by increments of ten. Press SET UP to save the setting and go to the next setting, or press /PLAY/STOP to save and exit set up mode. Set message alert tone This feature programs the system to beep every 10 seconds to alert you of new messages. The beeping will stop when all new messages have been reviewed. To set the message alert tone: 1. Press SET UP when in idle mode until the system announces the message alert tone setting. 2. Press /SKIP or /REPEAT to alternate between on or off, then press SET UP to save the setting, and go to the next setting or press /PLAY/STOP to save and exit set up mode. www.vtechphones.com 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61

www.vtechphones.com
29
Advanced operation
Answering system operation
Set telephone base ringer
This feature allows you to select the telephone base ringer volume levels.
You can choose from
HI
(high),
OF
(off) or
LO
(low).
To change the setting:
Press
SET UP
in idle mode until the system announces the telephone base ringer setting.
Press
/SKIP
or
/
REPEAT
until the system announces the desired telephone base ringer volume
level, then press
SET UP
to save the setting and go to the next setting or press
/
PLAY/STOP
to save and exit set up mode.
Set remote access code
A two-digit security code is required to access the answering system remotely from any touch tone
telephone. The code preset at the factory is
19
. You can set the code from
10
to
99
.
To set the remote access code:
Press
SET UP
when in idle mode until the system announces the remote access code setting.
Press
/
SKIP
or
/
REPEAT
to change the remote access code by one, or press and hold
/
SKIP
or
/
REPEAT
to change it by increments of ten.
Press
SET UP
to save the setting and go to the
next setting, or press
/
PLAY/STOP
to save and exit set up mode.
Set message alert tone
This feature programs the system to beep every 10 seconds to alert you of new messages. The
beeping will stop when all new messages have been reviewed.
To set the message alert tone:
Press
SET UP
when in idle mode until the system announces the message alert tone setting.
Press
/SKIP
or
/REPEAT
to alternate between on or off, then press
SET UP
to save the setting,
and go to the next setting or press
/PLAY/STOP
to save and exit set up mode.
1.
2.
1.
2.
1.
2.
• The answering
system must be
turned on for the
message alert tone
to function.