Weider Pro 325 Bench English Manual - Page 10

Attach the Rack Stabilizer 44 to the Rear

Get Weider Pro 325 Bench PDF manuals and user guides View all Weider Pro 325 Bench manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

16. Press a 30mm x 60mm Inner Cap (68) into the 16 end of the Rack Stabilizer (44). Press a 25mm Round Inner Cap (23) into the Rack Stabilizer. Attach the Rack Stabilizer (44) to the Rear Upright (49) with two M10 x 78mm Bolts (67), an M10 Washer (6), and two M10 Nylon Locknuts (11). Tighten the M10 Nylon Locknuts (11) used in steps 13, 15, and 16. 49 6 67 23 68 11 11 44 67 17. Route the Cable (58) up through the Rear Frame 17 (49) and around a Pulley (56), as shown. Attach the Pulley inside the Frame with an M10 x 75mm Bolt (66), two Long Spacers (69), two M10 Washers (6), and an M10 Nylon Locknut (11). 18. Wrap the Cable (58) around a Pulley (56). Attach 18 the Pulley and a Cable Trap (57) to the bracket on the Rear Upright (49) with an M10 x 47mm Bolt (24) and an M10 Nylon Locknut (11). Be sure the Cable Trap is on the outside of the bracket and turned to hold the Cable in the groove of the Pulley. 19. Attach the Cable (58) to the M10 x 22mm Bolt 19 (not shown) in the Weight Carriage (50) with an M10 Nylon Locknut (11). 56 6 11 69 58 6 49 69 66 57 58 11 56 24 49 58 11 50 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
10
17. Route the Cable (58) up through the Rear Frame
(49) and around a Pulley (56), as shown. Attach
the Pulley inside the Frame with an M10 x 75mm
Bolt (66), two Long Spacers (69), two M10
Washers (6), and an M10 Nylon Locknut (11).
17
24
11
50
58
49
23
49
16. Press a 30mm x 60mm Inner Cap (68) into the
end of the Rack Stabilizer (44). Press a 25mm
Round Inner Cap (23) into the Rack Stabilizer.
Attach the Rack Stabilizer (44) to the Rear
Upright (49) with two M10 x 78mm Bolts (67), an
M10 Washer (6), and two M10 Nylon Locknuts
(11).
Tighten the M10 Nylon Locknuts (11) used in
steps 13, 15, and 16.
16
68
6
58
11
67
56
69
69
66
11
6
6
44
67
18. Wrap the Cable (58) around a Pulley (56). Attach
the Pulley and a Cable Trap (57) to the bracket
on the Rear Upright (49) with an M10 x 47mm
Bolt (24) and an M10 Nylon Locknut (11).
Be
sure the Cable Trap is on the outside of the
bracket and turned to hold the Cable in the
groove of the Pulley.
18
19. Attach the Cable (58) to the M10 x 22mm Bolt
(not shown) in the Weight Carriage (50) with an
M10 Nylon Locknut (11).
19
49
58
56
11
57
11