Weider Pro 9000 Instruction Manual - Page 10

Pulley 24. Attach the Pulley to the Double U

Get Weider Pro 9000 PDF manuals and user guides View all Weider Pro 9000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

14. Wrap the Butterfly Cable (32) around a "V"-Pulley 14 (25). Attach the Pulley and a Large Cable Trap (27) to the bracket on the Centre Upright (5) with an M10 x 60mm Bolt (47) and an M10 Nylon Locknut (49). 49 Bracket 5 27 25 47 32 15. Remove the 90mm Pulleys (24) from the pre- 15 assembled Double "U"-Bracket (29). Wrap the Butterfly Cable (32) under a 90mm Pulley (24). Attach the Pulley to the Double "U"Bracket with an M10 x 45mm Bolt (57) and an M10 Nylon Locknut (49). 16. Wrap the Butterfly Cable (32) around a "V"-Pulley 16 (25). Attach the Pulley and a Large Cable Trap (27) to the bracket on the Centre Upright (5) with an M10 x 60mm Bolt (47) and an M10 Nylon Locknut (49). 24 32 49 57 29 47 25 32 27 49 Bracket 5 17. Attach the Butterfly Cable (32) to the bracket on 17 the Right Butterfly Arm (11) with an M8 x 22mm Shoulder Bolt (60) and an M8 Nylon Locknut (48). 11 48 Bracket 60 32 10 33. Orient the Seat (70) with the wide end on the side 33 shown. Attach the Seat to the Bench Frame (63) 70 with four M6 x 16mm Bolts (80). Wide End 63 34. Press three 45mm Square Inner Caps (42) into 34 the Leg Lever (66). Attach the Weight Tube (65) to the Leg Lever (66) with an M8 x 58mm Bolt (41), two M8 Washers (53), a 13mm x 10mm Spacer (75), and an M8 Nylon Locknut (48). Press a 25mm Round Inner Cap (45) into the indicated end of the Weight Tube (65). Press the 25mm Round Angle Cap (76) onto the other end of the Weight Tube. 80 80 42 42 45 75 41 53 65 42 66 76 48 53 35. Lubricate the M10 x 68mm Bolt (46) with grease. Attach the Leg Lever (66) to the Front Leg (64) with the Bolt and M10 Nylon Locknut (49). 36. Press the six 19mm Round Inner Caps (81) into the ends of the three Pad Tubes (71). Slide a Pad Tube (71) into the hole in the Front Leg (64). Slide two Foam Pads (72) onto the ends of the Pad Tube. Slide the other two Pad Tubes (71) into the holes in the Leg Lever (66). Slide two Foam Pads (72) onto each Pad Tube. 35 49 66 46 Lubricate 64 36 72 72 72 81 71 81 71 81 81 66 72 64 72 72 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
15
33. Orient the Seat (70) with the wide end on the side
shown. Attach the Seat to the Bench Frame (63)
with four M6 x 16mm Bolts (80).
10
14. Wrap the Butterfly Cable (32) around a “V”-Pulley
(25). Attach the Pulley and a Large Cable Trap
(27) to the bracket on the Centre Upright (5) with
an M10 x 60mm Bolt (47) and an M10 Nylon
Locknut (49).
16. Wrap the Butterfly Cable (32) around a “V”-Pulley
(25). Attach the Pulley and a Large Cable Trap
(27) to the bracket on the Centre Upright (5) with
an M10 x 60mm Bolt (47) and an M10 Nylon
Locknut (49).
17. Attach the Butterfly Cable (32) to the bracket on
the Right Butterfly Arm (11) with an M8 x 22mm
Shoulder Bolt (60) and an M8 Nylon Locknut (48).
15. Remove the 90mm Pulleys (24) from the pre-
assembled Double “U”-Bracket (29).
Wrap the Butterfly Cable (32) under a 90mm
Pulley (24). Attach the Pulley to the Double “U”-
Bracket with an M10 x 45mm Bolt (57) and an
M10 Nylon Locknut (49).
14
49
Bracket
47
25
27
32
5
15
24
57
49
29
16
17
48
60
11
32
47
32
49
5
27
Bracket
Bracket
25
32
34. Press three 45mm Square Inner Caps (42) into
the Leg Lever (66).
Attach the Weight Tube (65) to the Leg Lever (66)
with an M8 x 58mm Bolt (41), two M8 Washers
(53), a 13mm x 10mm Spacer (75), and an M8
Nylon Locknut (48).
Press a 25mm Round Inner Cap (45) into the
indicated end of the Weight Tube (65). Press the
25mm Round Angle Cap (76) onto the other end
of the Weight Tube.
35. Lubricate the M10 x 68mm Bolt (46) with grease.
Attach the Leg Lever (66) to the Front Leg (64)
with the Bolt and M10 Nylon Locknut (49).
33
34
35
36
70
63
80
42
45
65
76
41
53
48
53
75
42
42
66
72
72
72
72
66
64
81
81
81
81
71
71
72
72
49
46
64
80
Wide
End
66
Lubricate
36. Press the six 19mm Round Inner Caps (81) into
the ends of the three Pad Tubes (71).
Slide a Pad Tube (71) into the hole in the Front
Leg (64). Slide two Foam Pads (72) onto the
ends of the Pad Tube.
Slide the other two Pad Tubes (71) into the holes
in the Leg Lever (66). Slide two Foam Pads (72)
onto each Pad Tube.