Whirlpool WFE510S0AS Installation Guide - Page 13

Level Range, Warming Drawer or Premium Storage, Drawer - gas

Page 13 highlights

3. If the rear of the range lifts more than ½" (1.3 cm) off the floor without resistance, stop tilting the range and lower it gently back to the floor. The range foot is not engaged in the anti-tip bracket. IMPORTANT: If there is a snapping or popping sound when lifting the range, the range may not be fully engaged in the bracket. Check to see if there are obstructions keeping the range from sliding to the wall or keeping the range foot from sliding into the bracket. Verify that the bracket is held securely in place by the mounting screws. 4. Slide the range forward, and verify that the anti-tip bracket is securely attached to the floor or wall. 5. Slide range back so the rear range foot is inserted into the slot of the anti-tip bracket. IMPORTANT: If the back of the range is more than 2" (5.1 cm) from the mounting wall, the rear range foot may not engage the bracket. Slide the range forward and determine if there is an obstruction between the range and the mounting wall. Changes to the gas supply must be performed by a qualified service technician. If you need assistance or service, refer to the "Assistance or Service" section of the Use and Care Guide, or the cover or "Warranty" section of the User Instructions, for contact information. 6. Repeat steps 1 and 2 to ensure that the range foot is engaged in the anti-tip bracket. If the rear of the range lifts more than ½" (1.3 cm) off the floor without resistance, the anti-tip bracket may not be installed correctly. Do not operate the range without anti-tip bracket installed and engaged. Please reference the "Assistance or Service" section of the Use and Care Guide, or the cover or "Warranty" section of the User Instructions, to contact service. Level Range Determine if you have AquaLift™ Technology or Steam Clean by referring to the "Range Care" section of the User Instructions. For Ranges with AquaLift™ Technology or Steam Clean: 1. Place level on the oven bottom as indicated in one of the two figures below depending on the size of the level. Check with the level side to side and front to back. Style 1: Ranges Equipped with a Storage Drawer: Use a ¼" drive ratchet, wrench or pliers to adjust leveling legs up or down until the range is level. Push range back into position. Check that rear leveling leg is engaged in the anti-tip bracket. Style 2: Ranges Equipped with a Warming Drawer or Premium Storage Drawer: Use a wrench or pliers to adjust leveling legs up or down until the range is level. Push range back into position. Check that rear leveling leg is engaged in the anti-tip bracket. NOTE: Range must be level for satisfactory baking performance and best cleaning results using AquaLift™ Technology and Steam Clean functions. Warming Drawer or Premium Storage Drawer (on some models) Remove all items from inside the warming drawer or premium storage drawer, and allow the range to cool completely before attempting to remove the drawer. To Remove: 1. Open the warming drawer or premium storage drawer to its fully open position. 2. Using a flat-blade screwdriver gently loosen the warming drawer or premium storage drawer from the glide alignment notch and lift up the drawer alignment tab from the glide. A B C 2. If range is not level, pull range forward until rear leveling leg is removed from the anti-tip bracket. 3. Follow the directions in Style 1 or Style 2, depending on the style of drawer supplied with the range. For Ranges without AquaLift™ Technology or Steam Clean: 1. Place a standard flat rack in oven. 2. Place level on the rack and check levelness of the range, first side to side; then front to back. A. Flat-blade screwdriver B. Drawer alignment tab C. Drawer glide notch 3. Repeat Step 2 on the other side. The warming drawer or premium storage drawer is no longer attached to the drawer glides. Using both hands, pick up the warming drawer or premium storage drawer to complete the removal. 3. If range is not level, pull range forward until rear leveling leg is removed from the anti-tip bracket. 4. Follow the directions in Style 1 or Style 2, depending on the style of drawer supplied with the range. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

13
3.
If the rear of the range lifts more than ½" (1.3 cm) off the floor
without resistance, stop tilting the range and lower it gently
back to the floor. The range foot is not engaged in the anti-tip
bracket.
IMPORTANT:
If there is a snapping or popping sound when lifting
the range, the range may not be fully engaged in the bracket.
Check to see if there are obstructions keeping the range from
sliding to the wall or keeping the range foot from sliding into the
bracket. Verify that the bracket is held securely in place by the
mounting screws.
4.
Slide the range forward, and verify that the anti-tip bracket is
securely attached to the floor or wall.
5.
Slide range back so the rear range foot is inserted into the
slot of the anti-tip bracket.
IMPORTANT:
If the back of the range is more than 2" (5.1 cm) from
the mounting wall, the rear range foot may not engage the bracket.
Slide the range forward and determine if there is an obstruction
between the range and the mounting wall. Changes to the gas
supply must be performed by a qualified service technician. If you
need assistance or service, refer to the “Assistance or Service”
section of the Use and Care Guide, or the cover or “Warranty”
section of the User Instructions, for contact information.
6.
Repeat steps 1 and 2 to ensure that the range foot is
engaged in the anti-tip bracket.
If the rear of the range lifts more than ½" (1.3 cm) off the floor
without resistance, the anti-tip bracket may not be installed
correctly. Do not operate the range without anti-tip bracket
installed and engaged. Please reference the “Assistance or
Service” section of the Use and Care Guide, or the cover or
“Warranty” section of the User Instructions, to contact service.
Level Range
Determine if you have AquaLift™ Technology or Steam Clean by
referring to the “Range Care” section of the User Instructions.
For Ranges with AquaLift™ Technology or Steam Clean:
1.
Place level on the oven bottom as indicated in one of the two
figures below depending on the size of the level. Check with
the level side to side and front to back.
2.
If range is not level, pull range forward until rear leveling leg is
removed from the anti-tip bracket.
3.
Follow the directions in Style 1 or Style 2, depending on the
style of drawer supplied with the range.
For Ranges without AquaLift™ Technology or Steam Clean:
1.
Place a standard flat rack in oven.
2.
Place level on the rack and check levelness of the range, first
side to side; then front to back.
3.
If range is not level, pull range forward until rear leveling leg is
removed from the anti-tip bracket.
4.
Follow the directions in Style 1 or Style 2, depending on the
style of drawer supplied with the range.
Style 1: Ranges Equipped with a Storage Drawer:
Use
a ¼" drive ratchet, wrench or pliers to adjust leveling legs
up or down until the range is level. Push range back into
position. Check that rear leveling leg is engaged in the anti-tip
bracket.
Style 2: Ranges Equipped with a Warming Drawer or
Premium Storage Drawer:
Use a wrench or pliers to adjust leveling legs up or down until
the range is level. Push range back into position. Check that
rear leveling leg is engaged in the anti-tip bracket.
NOTE:
Range must be level for satisfactory baking
performance and best cleaning results using AquaLift™
Technology and Steam Clean functions.
Warming Drawer or Premium Storage
Drawer
(on some models)
Remove all items from inside the warming drawer or premium
storage drawer, and allow the range to cool completely before
attempting to remove the drawer.
To Remove:
1.
Open the warming drawer or premium storage drawer to its
fully open position.
2.
Using a flat-blade screwdriver gently loosen the warming
drawer or premium storage drawer from the glide alignment
notch and lift up the drawer alignment tab from the glide.
3.
Repeat Step 2 on the other side. The warming drawer or
premium storage drawer is no longer attached to the drawer
glides. Using both hands, pick up the warming drawer or
premium storage drawer to complete the removal.
A. Flat-blade screwdriver
B. Drawer alignment tab
C. Drawer glide notch
A
B
C