Whirlpool WTW2000H Owners Manual - Page 19

Winter storage care, Non-use and vacation care, Transporting your washer, Reinstalling/using washer

Get Whirlpool WTW2000H PDF manuals and user guides View all Whirlpool WTW2000H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Washer care (cont.) Cleaning The Lint Filter Clean filter after every load. 1. Press down, then out to remove the lint filter. 2. Open the lint filter and clean with water. Non-use and vacation care Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps: 1. Unplug or disconnect power to washer. 2. Turn off water supply to washer to avoid flooding due to water pressure surges. 3. Clean the dispensers. See "Cleaning the Dispensers." Winter storage care IMPORTANT: To avoid damage, install and store washer where it will not freeze. Because some water may stay in hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer. To winterize washer: 1. Shut off both water faucets; disconnect and drain water inlet hoses. 2. Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum and run washer on Normal cycle for about 2 minutes to mix antifreeze and remaining water. 3. Unplug washer or disconnect power. 3. Insert the lint filter bottom first, then press down and in to replace the filter. Transporting your washer 1. Shut off both water faucets. Disconnect and drain water inlet hoses. 2. If washer will be moved during freezing weather, follow WINTER STORAGE CARE directions before moving. 3. Disconnect drain hose from drain system and from back of washer. 4. Unplug power cord. 5. Place inlet hoses and drain hose inside washer drum. 6. Bundle power cord with a rubber band or cable tie to keep it from hanging onto the ground. Reinstalling/using washer again To reinstall washer after non-use, vacation, winter storage, or moving: 1. Refer to Installation Instructions to locate, level, and connect washer. 2. Before using again, run washer through the following recommended procedure: To use washer again: 1. Flush water pipes and hoses. Reconnect water inlet hoses. Turn on both water faucets. 2. Plug in washer or reconnect power. 3. Run washer through Heavy Duty cycle to clean washer and remove antifreeze, if used. Use only HE detergent. Use half the manufacturer's recommended amount for a medium-size load. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
19
Operate your washer only when you are home. If moving,
or not using your washer for a period of time, follow these
steps:
1.
Unplug or disconnect power to washer.
2.
Turn off water supply to washer to avoid flooding due to
water pressure surges.
3.
Clean the dispensers. See “Cleaning the Dispensers.”
Winter storage care
IMPORTANT:
To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1.
Shut off both water faucets; disconnect and drain water
inlet hoses.
2.
Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum and
run washer on Normal cycle for about 2 minutes to mix
antifreeze and remaining water.
3.
Unplug washer or disconnect power.
Non-use and vacation care
Transporting your washer
1.
Shut off both water faucets. Disconnect and drain water
inlet hoses.
2.
If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3.
Disconnect drain hose from drain system and from back
of washer.
4.
Unplug power cord.
5.
Place inlet hoses and drain hose inside washer drum.
6.
Bundle power cord with a rubber band or cable tie to
keep it from hanging onto the ground.
Reinstalling/using washer again
To reinstall washer after non-use, vacation, winter storage,
or moving:
1.
Refer to Installation Instructions to locate, level, and
connect washer.
2.
Before using again, run washer through the following
recommended procedure:
To use washer again:
1.
Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
2.
Plug in washer or reconnect power.
3.
Run washer through Heavy Duty cycle to clean washer
and remove antifreeze, if used. Use only HE detergent.
Use half the manufacturer’s recommended amount for a
medium-size load.
Cleaning The Lint Filter
Clean filter after every load.
1.
Press down, then out to remove the lint filter.
2.
Open the lint filter and clean with water.
3.
Insert the lint filter bottom first, then press down and in to
replace the filter.
Washer care (cont.)