Xerox 850DX Xerox Wide Format 8825/8830/8850/8855/X2 Tech System Introduction - Page 77

Printer Feature, Description/Specifications, 8850 - N5T/CNG Controller Specifications, I/O Ports

Get Xerox 850DX - Phaser Color Solid Ink Printer PDF manuals and user guides
UPC - 042215454865
View all Xerox 850DX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Printer Feature Description/Specifications 8830/8850 - N5T/CNG Controller Specifications Hardware Specifications CPU: Power PC 740 200 MHz, 8.5 SpecInt95, 16.0 SpecFP9 (estimated) 64 MB RAM is standard. Maximum RAM is 192 MB. Hard disk: 9.1 GB, Ultra SCSI, 7200 rpm internal hard disk drive standard on CNG. (Required option for N5T running 6.0+ firmware) Physical Characteristics Electrical Requirements Agency Approvals I/O Ports Serial (2) The Controller is attached to the side panel of XES Synergix 8825/8830 Printer as an embedded device. 100 - 250 VAC auto-ranging power supply. Safety: UL 1950, CA22.2 No. 950 (CUL), EN 60950 (CE Mark) EMC: CE Mark, FCC Class A, Canada Radio Interference Regulations Class A, VCCI Class 1 Two 9 pin Host serial ports provided. One is used by the 8825/8830 Digital Solution scanner when this option is connected. The second is used as an input port for receiving data via serial port connection. Note: For firmware releases 1.0 − 2.0, the upper serial port is used for data input; the lower serial port is used for service. For later releases, the upper serial port is used for connection to the 8825/8830 Scanner Control Panel if a scanner is detected during startup. If a scanner is not detected during startup, the upper serial port becomes the service port. Parallel SCSI VPI Scanner Ethernet Option IEEE 1394 The lower serial port is used for data input. (IEEE 1284 Compliant) High density port connector provided. 50 pin Ultra SCSI Connector provided. 37 pin D Connector provided. 50 pin Ultra SCSI Connector provided. Built-in 10/100 Ethernet Network Interface: RJ-45 connection, supporting TCP/IP only. Optional External Ethernet Adapter available to support TCP/IP, Novell 3.x, 4.x, 5.x, and NetBEUI. Interface supporting the Synergix Scan System. XES Synergix 8825/8830/8850/8855 & X2-TECH System Introduction 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
XES Synergix 8825/8830/8850/8855 & X2-TECH System Introduction
69
Printer Feature
Description/Specifications
8830/8850 - N5T/CNG Controller Specifications
Hardware Specifications
CPU:
Power PC 740 200 MHz, 8.5 SpecInt95, 16.0 SpecFP9 (estimated)
64 MB RAM is standard.
Maximum RAM is 192 MB.
Hard disk:
9.1 GB, Ultra SCSI, 7200 rpm internal hard disk drive standard on CNG.
(Required option for N5T running 6.0+ firmware)
Physical Characteristics
The Controller is attached to the side panel of XES Synergix 8825/8830 Printer as an embedded device.
Electrical Requirements
100 - 250 VAC auto-ranging power supply.
Agency Approvals
Safety: UL 1950, CA22.2 No. 950 (CUL), EN 60950 (CE Mark)
EMC: CE Mark, FCC Class A, Canada Radio Interference Regulations Class A, VCCI Class 1
I/O Ports
Serial (2)
Two 9 pin Host serial ports provided.
One is used by the 8825/8830 Digital Solution scanner when this option is connected.
The second
is used as an input port for receiving data via serial port connection.
Note:
For firmware releases 1.0
−
2.0, the upper serial port is used for data input; the lower serial port is used for service.
For later releases, the upper serial port is used for connection to the 8825/8830 Scanner Control Panel if a scanner is detected during
startup.
If a scanner is not detected during startup, the upper serial port becomes the service port.
The lower serial port is used for data input.
Parallel
(IEEE 1284 Compliant) High density port connector provided.
SCSI
50 pin Ultra SCSI Connector provided.
VPI
37 pin D Connector provided.
Scanner
50 pin Ultra SCSI Connector provided.
Ethernet
Built-in 10/100 Ethernet Network Interface:
RJ-45 connection, supporting TCP/IP only.
Option
Optional External Ethernet Adapter available to support TCP/IP, Novell 3.x, 4.x, 5.x, and NetBEUI.
IEEE 1394
Interface supporting the Synergix Scan System.