Yamaha 24N DME64N/24N V1.2 Supplemental notes
Yamaha 24N Manual
 |
View all Yamaha 24N manuals
Add to My Manuals
Save this manual to your list of manuals |
Yamaha 24N manual content summary:
- Yamaha 24N | DME64N/24N V1.2 Supplemental notes - Page 1
Manual about DME64N/DME24N Version 1.2 simultaneously. For instructions on performing the version Manual." • To use the DME CONTROL function on the PM5D, the PM5D must be version 1.12 or later, and connected DME64N/24N document can be found at the Yamaha Pro Audio website: http://www.yamahaproaudio. - Yamaha 24N | DME64N/24N V1.2 Supplemental notes - Page 2
Designer, see the "DME Designer Version 1.2 Owner's Manual." ■ The default gateway IP address is changed. function has been added. With this function you can initialize the DME64N/24N and the ICP1. Turn the power OFF, then turn it back DME24N, the internal AD and internal DA are directly connected on - Yamaha 24N | DME64N/24N V1.2 Supplemental notes - Page 3
page. Refer to the "DME Designer Version 1.2 Owner's Manual" for details. Event Scheduler Determines whether an event schedule setup you can control the DME64N/24N from a DAW controller. 1. Parameter Control Function Lets you control DME64N/24N parameters using a DAW Controller. DME24N Version 1.2 3 - Yamaha 24N | DME64N/24N V1.2 Supplemental notes - Page 4
digits of the serial number. A fee is charged for the hardware upgrade. For details, contact Yamaha customer support using the contact information located at the end of the "DME64N/24N Owner's Manual." ■ The [PHONES] terminal can now be muted. The [PHONES] terminal in Version 1.0 was not muted - Yamaha 24N | DME64N/24N V1.2 Supplemental notes - Page 5
indicators also do not work in the DME24N. ■ There is an error on page 29 of the DME64N/24N Owner's Manual, where it states that there is support 100Base-TX, it operates as 10Base-T. ■ The following notes apply to the RS-232C terminal in "Control I/O)" on page 63 of the DME64N/24N Owner's Manual - Yamaha 24N | DME64N/24N V1.2 Supplemental notes - Page 6
DME Designer and the DME64N/24N unit. No MAC address is set. Since this is likely to be a device failure, contact a Yamaha electric sound service outlet listed at the end of this manual (page 79). Panel lock may be old. Update to the latest component. 6 Notes for DME64N/DME24N Version 1.2 - Yamaha 24N | DME64N/24N V1.2 Supplemental notes - Page 7
input. NOTE For information about updated CD-ROM versions to be released in the future, contact the store where you purchased the device, or contact Yamaha customer service using the contact information at the end or your "DME64N/24N Owner's Manual." Notes for DME64N/DME24N Version 1.2 7 - Yamaha 24N | DME64N/24N V1.2 Supplemental notes - Page 8
notes supplement the information in the DME64N/DME24N Owner's Manual DME24N ANALOG INPUT CHARACTERISTICS Terminals Gain CH INPUT -30dBFS @1kHz, phones level control: max. 0.1 % U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2005 Yamaha Corporation Printed in Japan
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
Notes for DME64N/DME24N Version 1.2
Thank you for purchasing the DME64N/DME24N. The following notes supplement the information in the Owner’s Manual
about DME64N/DME24N.
■
An Edit Indicator has been added.
If a parameter is changed after recalling a scene, a dot
will appear in the scene number indicator, and “EDIT”
will appear in the display.
■
The User-de
fi
ned parameters display is changed.
“No Assign” settings in DME Designer are displayed as
dotted lines.
When [Parameter Value Edit] is selected the display will
be a solid line.
When [Direct Parameter Value], [Scene Change], [GPI
Out], or [Play Wav File] are selected, the display will be
inverted.
■
The Remote parameter has been added to Utility display “Misc” page.
•
The REMOTE connector can be used as a MIDI connector.
•
A new communications protocol allows AMX, Crestron, and other external devices to control the DME.
For details about the communication protocol refer to the “DME-N Remote Control Protocol Specifications” document.
The “DME-N Remote Control Protocol Specifications” document can be found at the Yamaha Pro Audio website:
Added parameters are shown in bold.
Upgrading Cautions
•
The following parameter will not be reflected in Version 1.2 when it is used to read data created in Version 1.0.0: SlotIn/SlotOut.
Remake these settings in DME Designer Version 1.2.
•
Data created using Version 1.2 will not open properly on Version 1.1.
•
Version 1.2 will not work with previous version in the area. When using Version 1.2, all DME firmware (program and components),
along with DME Designer, must be upgraded to Version 1.2 simultaneously. For instructions on performing the version upgrade,
see “DME Firmware Update” in Chapter 3 “Main Panel Window” of the “DME Designer Version 1.2 Owner’s Manual.”
•
To use the DME CONTROL function on the PM5D, the PM5D must be version 1.12 or later, and connected DME64N/24N units
must be version 1.1 or later.
•
For details about DME CONTROL function settings in the PM5D, see the “PM5D/PM5D-RH Owner’s Manual.”
Changes in Version 1.2
HA Control (422)
External head amp control (RS-422 only)
COM (232C)
Control using the DME communication protocol via RS-232C/RS-422.
COM (422)
MIDI (232C)
Control using MIDI commands via RS-232C/RS-422.
MIDI (422)
Remote Ctrl (232C)
Remote controller via RS-232C/RS-422.
Remote Ctrl (422)
EN