Yamaha DPX-530 Owner's Manual - Page 38

Indicators, Normal conditions

Page 38 highlights

15 Indicators This projector has two indicators, each of which shows the operation condition of the projector. Refer to Troubleshooting for additional indication signals. POWER indicator STATUS indicator STANDBY/ON button ◆ Normal conditions POWER STATUS CONDITION Stand-by. Steady red Off Warming up period (about 1 minute). Steady green Blinking green The projector is ready. Steady green Steady red Steady green Blinking green Cooling down period (lasts under 2 minutes; normal when shutting down). ◆ Abnormal conditions NOTE The STANDBY/ON button cannot be used until the STATUS indicator is steady green. Do not unplug the projector until the STATUS indicator is off. POWER STATUS CONDITION SOLUTION Steady green or Steady red Steady red Blinking orange Blinking green Abnormal temperature • The ventilation grilles are clogged with dust or dirt. • The room temperature is high. • Clean the ventilation grilles. • Relocate the projector to a cooler place. • Remove any objects blocking the ventilation grilles. Abnormal when it occurs except while shutting down. The protection circuit is working or the lamp is in an abnormal condition. • Wait until the STATUS indicator goes out, then press the STANDBY/ON button. • If the above solution is not effective, replace the lamp. Lamp operation time warning. (Total lamp operation time reached 3000 hours*1 while the power was on.) Steady green Blinking green/red Steady red Blinking red Lamp operation time warning. (Total lamp operation time reached 3000 hours*1 while the power was off.) Steady red Steady red Lamp operation time warning. (Total lamp operation time reached 4000 hours*1, *2 while the power was off.) The lamp cover isn't closed. Replace the lamp. Change with a new lamp if this problem recurs. Close the cover correctly. Blinking green/red Off Abnormal. Contact your dealer. Blinking green/red Steady or Blinking *1: When LAMP MODE of the SETUP menu is set to CINEMA. When it is set to BRIGHT, this duration will be decreased. *2: When LAMP MODE is set to BRIGHT, this duration will be decreased to 2000 hours. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42

34
This projector has two indicators, each of which shows the operation condition of the projector.
Refer to Troubleshooting for additional indication signals.
Normal conditions
Abnormal conditions
*1:
When LAMP MODE of the SETUP menu is set to CINEMA. When it is set to BRIGHT, this duration will be decreased.
*2:
When LAMP MODE is set to BRIGHT, this duration will be decreased to 2000 hours.
POWER
STATUS
CONDITION
NOTE
Steady red
Off
Stand-by.
Steady green
Blinking green
Warming up period (about 1 minute).
The STANDBY/ON button cannot be used
until the STATUS indicator is steady green.
Steady green
Steady green
The projector is ready.
Steady red
Blinking green
Cooling down period (lasts under 2 minutes; normal when
shutting down).
Do not unplug the projector until the
STATUS indicator is off.
POWER
STATUS
CONDITION
SOLUTION
Steady green
or
Steady red
Blinking orange
Abnormal temperature
The ventilation grilles are clogged with dust or dirt.
The room temperature is high.
Clean the ventilation grilles.
Relocate the projector to a cooler place.
Remove any objects blocking the
ventilation grilles.
Steady red
Blinking green
Abnormal when it occurs except while shutting down. The
protection circuit is working or the lamp is in an abnormal
condition.
Wait until the STATUS indicator goes out,
then press the STANDBY/ON button.
If the above solution is not effective,
replace the lamp.
Steady green
Blinking green/red
Lamp operation time warning. (Total lamp operation time
reached 3000 hours
*1
while the power was on.)
Replace the lamp.
Change with a new lamp if this problem
recurs.
Steady red
Blinking red
Lamp operation time warning. (Total lamp operation time
reached 3000 hours
*1
while the power was off.)
Steady red
Steady red
Lamp operation time warning. (Total lamp operation time
reached 4000 hours
*1, *2
while the power was off.)
Blinking
green/red
Off
The lamp cover isn’t closed.
Close the cover correctly.
Blinking
green/red
Steady or
Blinking
Abnormal.
Contact your dealer.
STATUS indicator
POWER indicator
STANDBY/ON button
Indicators
15