Yamaha DTX700 Reference Manual - Page 11

Internal Design of the DTX700 Parameter name EQ3Q EQ4Freq EQ4Gain EQ4Q EQ5Freq EQ5Gain ER/Rev F/RDpth FBHiDmp FBLevel FBLvl1 FBLvl2 FBTime FBTime1 FBTime2 FBTimeL FBTimeR Feedback Fine1 Fine2 H.Freq H.Gain Height Descriptions This parameter is used to set the resonance of the EQ3 band. This parameter is used to set the center frequency for the EQ4 band. This parameter is used to set the gain for the EQ4 band. This parameter is used to set the resonance of the EQ4 band. This parameter is used to set the cutoff frequency for the EQ5 band (i.e., high shelving). This parameter is used to set the gain for the EQ5 band (i.e., high shelving). This parameter is used to set the relative volumes of early reflections and reverberation. This parameter is used to set the front-to-rear pan depth (and is valid only when PanDirectn is set to "Lturn" or "Rturn"). This parameter is used to set how the feedback sound decays in the high-frequency band (with smaller values corresponding to faster decay). [Chorus effects, Delay effects, and TempoFlanger] This parameter is used to set how much of the delay sound is fed back into the effect's input (with negative values indicating that its phase is to be inverted). [TempoPhaser] This parameter is used to set how much of the phaser's output is fed back into its input (with negative values indicating that its phase is to be inverted). [Reverb effects] This parameter is used to set the initial delay's feedback level. This parameter is used to set the feedback level for the first delay sound. This parameter is used to set the feedback level for the second delay sound. This parameter is used to set the feedback delay time. This parameter is used to set the delay time for feedback delay 1. This parameter is used to set the delay time for feedback delay 2. This parameter is used to set the delay time for the left feedback delay. This parameter is used to set the delay time for the right feedback delay. This parameter is used to set how much of the effect's output is fed back into its input. This parameter is used to adjust the first fine-pitch setting. This parameter is used to adjust the second finepitch setting. This parameter is used to set the center frequency of the high-frequency EQ band. This parameter is used to set the amount by which the high-frequency EQ band is boosted or cut. This parameter is used to set the height of the simulated room. Parameter name HiAtk HiGain HiLvl HiMute HiRat HiTh HornF HornS HPF InitDly InitDly1 InitDly2 InitDlyL InitDlyR InpMode InpSelect L.Freq L.Gain L/RDiffuse L/RDpth Lag LFODpth LFODiff Descriptions This parameter is used to set the amount of time that elapses before compression is fully applied in the high-frequency band. This parameter is used to set the output level of the high-frequency band. This parameter is used to set the high-frequency level. This parameter is used to activate and deactivate high-frequency muting. [MltBndComp] This parameter is used to set the compression ratio for the high-frequency band. [Reverb effects] This parameter is used to adjust the high-frequency component. This parameter is used to set the input-signal level at which the compressor starts to process the sound in the high-frequency band. This parameter is used to set the speed of rotation of the high-frequency horn at the "fast" setting. This parameter is used to set the speed of rotation of the high-frequency horn at the "slow" setting. This parameter is used to set the high-pass filter's cutoff frequency. This parameter is used to set the amount of time that elapses before early reflections are produced. This parameter is used to set the delay time for the first delay. This parameter is used to set the delay time for the second delay. This parameter is used to set the delay time for the left-channel delay. This parameter is used to set the delay time for the right-channel delay. This parameter is used to switch between mono and stereo input. This parameter is used to select an input. This parameter is used to set the center frequency of the low-frequency EQ band. This parameter is used to set the amount by which the low-frequency EQ band is boosted or cut. This parameter is used to set the difference between left and right delay times in order to produce a more spacious sound. This parameter is used to set the depth of the leftright panning effect. This parameter is used to set a time lag for delay times specified in terms of note lengths. [SPX Flanger, TempoFlanger, SPX Chorus, and Symphonic] This parameter is used to set the depth of modulation. [Tempo Phaser] This parameter is used to set the depth of phase modulation. This parameter is used to set the left-right phase difference between modulation waveforms. DTX700 Reference Manual 11