Yamaha EL-27 Owner's Manual - Page 32

Selecting from the Panel Buttons

Get Yamaha EL-27 PDF manuals and user guides View all Yamaha EL-27 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

2. Selecting from the Panel Buttons qReverb Reverb adds an echo-like effect to the sound, giving the impression of a performance in a large room or concert hall. The effect is applied equally and simultaneously to all voice sections. To adjust the reverb effect: Press one of the REVERB buttons, located at the far left of the panel. These controls determine the depth of the reverb effect. There are seven settings, from a minimum of 0, or no reverb, to the maximum. REVERB MAX 3 Voice Controls and Effects MIN qSustain Sustain is selectable for the Upper, Lower and Pedal voices and makes the sound gradually fade out when the keys are released. The sustain on/off and sustain length settings are independent for each keyboard, providing maximum expressive control. To add sustain to the voices and call up the Sustain Length page: 1. Press either of the buttons in the SUSTAIN section. The lamp of the button pressed lights up to indicate that sustain is on. Press the button again to turn sustain off. The Sustain display appears on the LCD display. SUSTAIN UPPER (KNEE) LOWER (KNEE) PEDAL Sustain cannot be applied to the Lead voices. If knee lever control of the Upper or Lower sustain has been turned on, pressing the Upper or Lower buttons here will not add sustain unless the knee lever is pushed. (See page 52.) Remember that the SUSTAIN buttons are on/off switches. If you use them to simply check the sustain length values, you may unintentionally change the on/off status of the effect. Remember to check whether the sustain button lamps are on or off before you start to play. UPPER=10 LOWER=10 PEDAL=6 When you turn off and turn on the Electone again, the voice is set to the Basic Registration 1. Be sure to store the selected voices (registration setting) to the Registration Memory before you turn off the Electone (see page 47.). 2. Determines the length of sustain applied to each voice section by using each of the DATA CONTROL buttons. The display shows the current sustain length values for each voice section. 30 Increasing values makes sustain more effectively. Range:0 - 12.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
30
3 Voice Controls and Effects
2. Selecting from the Panel Buttons
●
Reverb
Reverb adds an echo-like effect to the sound, giving the impression of a
performance in a large room or concert hall. The effect is applied equally
and simultaneously to all voice sections.
To adjust the reverb effect:
Press one of the REVERB buttons, located at the far left of the panel.
These controls determine the depth of the reverb effect. There are seven
settings, from a minimum of 0, or no reverb, to the maximum.
●
Sustain
Sustain is selectable for the Upper, Lower and Pedal voices and makes the
sound gradually fade out when the keys are released. The sustain on/off
and sustain length settings are independent for each keyboard, providing
maximum expressive control.
To add sustain to the voices and call up the
Sustain Length page:
1.
Press either of the buttons in the SUSTAIN section.
The lamp of the button pressed lights up to indicate that sustain is on.
Press the button again to turn sustain off.
The Sustain display appears on the LCD display.
2.
Determines the length of sustain applied to each
voice section by using each of the DATA CONTROL
buttons.
The display shows the current sustain length values for each voice section.
Increasing values makes sustain more effectively. Range:0 – 12.
<SUSTAIN> UPPER=10
LOWER=10
PEDAL=6
UPPER
(KNEE)
LOWER
(KNEE)
PEDAL
SUSTAIN
MAX
MIN
REVERB
Sustain cannot be applied to
the Lead voices.
If knee lever control of the
Upper or Lower sustain has
been turned on, pressing the Upper or
Lower buttons here will not add
sustain unless the knee lever is
pushed. (See page 52.)
Remember that the SUSTAIN
buttons are on/off switches. If
you use them to simply check the
sustain length values, you may
unintentionally change the on/off
status of the effect. Remember to
check whether the sustain button
lamps are on or off before you start to
play.
When you turn off and turn
on the Electone again, the
voice is set to the Basic
Registration 1. Be sure to store the
selected voices (registration
setting) to the Registration
Memory before you turn off the
Electone (see page 47.).