Yamaha MRX-100 MRX-100 OWNERS MANUAL - Page 15

controller

Get Yamaha MRX-100 PDF manuals and user guides View all Yamaha MRX-100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Symptom ERROR/ BATT. indicator status Possible Cause Remedy, Multi-cornmand programming is impossible Blinks three Batteries are nearly exhausted. times Replace the batteries of the MRX-100 with new ones. Multi-command operation is impossible Blinks three times Batteries are nearly exhausted. Replace the batteries of I the MRX-100 with new ones. The signal stored under each learning key is incorrct. Check the operation stored in each learning key beforehand. The order of the multi-command operation is unsuitable. Perform the programming again in the correct order. Remote sensor of the object component is Operate it at placed too far away from the MRX-100. the closer position. The remote sensor of the object component is obstructed. Remove the obstacle so as not to block the remote sensor. The object componetns do not function in Change the correspondence with a signal continuously sequence of transmitted (series signal) from the the MRX-100. multi-com- mand operations. / • Immediately after turning the power ON, or when an object component needs a long processing time, the multi-command operation of the succeeding signal may not be accepted. In this case, insert a signal to change the input selection of an amplifier, etc. between the signals for the multi-command operation so that a certain margin is given to the • sequential operation. / If the problem still persists after checking these points, the signal coding and modulation system of the other remote controller are probably different from those of the MRX-100 and the MRX-100 cannot "learn" them. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
Symptom
ERROR/
BATT.
indicator
status
Possible
Cause
Remedy,
Multi
-corn-
mand
program-
ming
is
impossible
Blinks
three
times
Batteries
are
nearly
exhausted.
Replace
the
batteries
of
the
MRX-100
with
new
ones.
Multi-com-
mand
operation
is
impossible
Blinks
three
times
Batteries
are
nearly
exhausted.
Replace
the
batteries
of
I
the
MRX-100
with
new
ones.
The
signal
stored
under
each
learning
key
Check
the
is
incorrct.
operation
stored
in
each
learning
key
beforehand.
The
order
of
the
multi
-command
operation
Perform
the
is
unsuitable.
programming
again
in
the
correct
order.
Remote
sensor
of
the
object
component
is
Operate
it
at
placed
too
far
away
from
the
MRX-100.
the
closer
position.
The
remote
sensor
of
the
object
Remove
the
component
is
obstructed.
obstacle
so
as
not
to
block
the
remote
sensor.
The
object
componetns
do
not
function
in
Change
the
correspondence
with
a
signal
continuously
sequence
of
transmitted
(series
signal)
from
the
the
MRX-100.
multi
-com-
mand
operations.
/
•
Immediately
after
turning
the
power
ON,
or
when
an
object
component
needs
a
long
processing
time,
the
multi
-command
operation
of
the
succeeding
signal
may
not
be
accepted.
In
this
case,
insert
a
signal
to
change
the
input
selection
of
an
amplifier,
etc.
between
the
signals
for
the
multi
-command
operation
so
that
a
certain
margin
is
given
to
the
sequential
operation.
•
/
If
the
problem
still
persists
after
checking
these
points,
the
signal
coding
and
modulation
system
of
the
other
remote
controller
are
probably
different
from
those
of
the
MRX-100
and
the
MRX-100
cannot
"learn"
them.
14