Yamaha PGX1 PGM1/PGX1 Installation Manual - Page 11

Bottom Panel, Dante/NETWORK connector, SYNC indicator, LINK/ACT indicator, pin dedicated connector

Get Yamaha PGX1 PDF manuals and user guides View all Yamaha PGX1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Controls and Connectors (PGM1) • Switches 7-8 (START UP MODE) Specify how the unit is initialized after the power turns on. Switch 78 Setting RESUME Content This is the normal operating mode. When the PGM1's power is turned on, it starts up while preserving the state in which it was immediately prior to powering-off. Switch Setting 78 INT. (INITIALIZE) Content The unit is initialized to the factory settings (page 13). e Dante/NETWORK connector This is an RJ-45 port for connecting a Dante device such as the MRX7-D using an Ethernet cable (CAT5e or better) via PSE. NOTE • Do not connect anything other than a Dante- enabled device or a device that supports gigabit Ethernet (including computers). • The maximum cable length that can be used is 100 meters. • Use STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. r SYNC indicator This indicator shows the operating status of the Dante network. When the green indicator is lit, this indicates that the unit is the clock slave and that the clock is synchronized. When the green indicator is flashing, this indicates that the unit is the clock master. t LINK/ACT indicator This indicator shows the communication status of the Dante/NETWORK connector. If the Ethernet cable is connected correctly, the indicator flashes rapidly. Bottom Panel q q 8-pin dedicated connector This is a dedicated connector for connection to the PGX1. When the unit is shipped from the factory, a rubber cap is attached here. PGM1/PGX1 Installation Manual 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
Controls and Connectors (PGM1)
11
PGM1/PGX1 Installation Man
u
al
• Switches 7–8 (START UP MODE)
Specify ho
w
the
u
nit is initialized after
the po
w
er t
u
rns on.
e
Dante/NETWORK connector
This is an RJ-45 port for connecting a
Dante de
v
ice s
u
ch as the MRX7-D
u
sing
an Ethernet ca
b
le (CAT5e or
b
etter)
v
ia
PSE.
r
SYNC indicator
This indicator sho
w
s the operating stat
u
s
of the Dante net
w
ork.
When the green indicator is lit, this indi-
cates that the
u
nit is the clock sla
v
e and
that the clock is synchronized.
When the green indicator is flashing, this
indicates that the
u
nit is the clock master.
t
LINK/ACT indicator
This indicator sho
w
s the comm
u
nication
stat
u
s of the Dante/NETWORK connector.
If the Ethernet ca
b
le is connected cor-
rectly, the indicator flashes rapidly.
Bottom Panel
q
8-pin dedicated connector
This is a dedicated connector for connec-
tion to the PGX1.
When the
u
nit is shipped from the factory,
a r
ubb
er cap is attached here.
Switch
Settin
g
RESUME
Content
This is the normal operating
mode.
When the PGM1’s po
w
er is
t
u
rned on, it starts
u
p
w
hile
preser
v
ing the state in
w
hich it
w
as immediately prior to po
w
-
ering-off.
Switch
Settin
g
INT. (INITIALIZE)
Content
The
u
nit is initialized to the fac-
tory settings (page 13).
NOTE
•
Do not connect anything other than a Dante-
ena
b
led de
v
ice or a de
v
ice that s
u
pports
giga
b
it Ethernet (incl
u
ding comp
u
ters).
•
The maxim
u
m ca
b
le length that can
b
e
u
sed is 100 meters.
•
Use STP (Shielded T
w
isted Pair) ca
b
le to
pre
v
ent electromagnetic interference.
7
8
7
8
q