Yamaha YDP-V240 Owner's Manual - Page 115

Attach the adjuster to C., Attach finger-tighten D and E to C., Attach B., Secure C.

Get Yamaha YDP-V240 PDF manuals and user guides View all Yamaha YDP-V240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 115 highlights

Keyboard Stand Assembly 1 Attach the adjuster to C. 1-1 Align the tip of the adjuster with the screw hole, then screw in the adjuster all the way until it stops turning. You will adjust the height of the adjuster in Step 8. 1-2 Untie and straighten out the bundled cord. Don't discard the vinyl tie, you'll need it later in Step 7. 1-2 1-1 C 2 Attach (finger-tighten) D and E to C. 2-1 Align D and E with each end of C. 2-2 Attach D and E to C by finger-tightening the long screws (6 x 20mm). 3 Attach B. 3-1 Place the lower side of B on each foot of D and E, then attach the upper side to D and E. 3-2 Attach the top of B to D and E by finger-tightening the thin screws (4 x 12mm). 3-3 While pushing the lower outside part of D and E towards each other, secure the bottom of B at each end using two tapping screws (4 x 20mm). 3-4 Insert the other two tapping screws (4 x 20mm) into the other two screw holes to secure B. 3-5 While pushing D and E towards each other, securely tighten the screws that were fingertightened in Step 3-2. 3-2 3-5 E B D E 2-2 D C 3-3 3-4 4 Secure C. 4-1 Securely tighten the screws on C that were attached in Step 2-2. D B E C 4-1 Owner's Manual 115

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
Owner’s Manual
115
Keyboard Stand Assembly
1
Attach the adjuster to C.
1-1
Align the tip of the adjuster with the screw
hole, then screw in the adjuster all the way
until it stops turning.
You will adjust the height of the adjuster in
Step 8.
1-2
Untie and straighten out the bundled cord.
Don’t discard the vinyl tie, you’ll need it later
in Step 7.
2
Attach (finger-tighten) D and E to C.
2-1
Align D and E with each end of C.
2-2
Attach D and E to C by finger-tightening the
long screws (6 x 20mm).
3
Attach B.
3-1
Place the lower side of B on each foot of D and
E, then attach the upper side to D and E.
3-2
Attach the top of B to D and E by finger-tight-
ening the thin screws (4 x 12mm).
3-3
While pushing the lower outside part of D and
E towards each other, secure the bottom of B
at each end using two tapping screws (4 x
20mm).
3-4
Insert the other two tapping screws (4 x
20mm) into the other two screw holes to
secure B.
3-5
While pushing D and E towards each other,
securely tighten the screws that were finger-
tightened in Step 3-2.
4
Secure C.
4-1
Securely tighten the screws on C that were
attached in Step 2-2.
1-1
1-2
C
C
E
D
2-2
B
D
E
3-2
3-5
3-3
3-4
D
B
E
C
4-1