Zenith SL-5597-BZ-E User Manual - Page 3

Mount the Light Control, Bulb Installation, Wire the Light Control

Get Zenith SL-5597-BZ-E - Heath - Quartz Halogen Motion-Sensing Twin Security Light PDF manuals and user guides
UPC - 016963559707
View all Zenith SL-5597-BZ-E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Bulb Installation Mount the Light Control NOTE: When re-lamping, turn power off and let the ❒ Place the mounting bolt through the front of the fixture cool. junction box cover. Push the small gasket hole over ❒ To remove lamp shade, loosen set screw 2 full the mounting screw. turns with a small flat-head screwdriver.Turn shade ❒ Make sure the wire connectors and wires are inside counterclockwise and remove. the junction box. Align the mounting screw with the ❒ To remove bulb, pull straight out of fixture. center hole in the mounting strap. Secure the fixture ❒ To replace bulb, push bulb pins into lamp socket. to the mounting strap. Check that the bulb is seated properly. ❒ Push the rubber plug firmly into place. ❒ To reinstall lamp shade, place shade on fixture and ❒ If a wet location junction box was not used, caulk align notches on shade with tabs on fixture. Turn the wall plate mounting surface with silicone weather clockwise. Tighten set screw firmly. sealant. Wire the Light Control WARNING: Turn power off at circuit breaker or fuse. Lamp Shade ❒ Remove the existing light fixture. ❒ Install the mounting strap as shown using two screws that fit your junction box. ❒ The plastic hanger can be used to hold the fixture Lock Nuts Set Screw while wiring. The small end of the plastic hanger can be threaded through the hole in the center of the cover plate. The small end then goes into one of the slots on the mounting strap. Keep lamps at least 2" (51 mm) from the sensor and 2" (51 mm) from combustibles. ❒ Route the light control's wires through the large gasket holes. ❒ Adjust the lamp holders by loosening the lock nuts, ❒ Twist the junction box wires and fixture wires together but do not rotate the lamp holders more than 180° as shown. Secure with wire connectors. from the factory setting. ❒ Adjust lamp shades by loosening the set screws several turns, turn shades counterclockwise and Mounting Black to Strap Black White to White remove. Reinstall the shades in the desired position and tighten set screws. Rubber Plug Gasket Junction box ground wire to green ground screw on fixture. Mounting Bolt 595-5679-08 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
3
595-5679-08
Keep lamps at least 2" (51 mm) from the
sensor and 2" (51 mm) from combustibles.
Lock Nuts
Mount the Light Control
❒
Place the mounting bolt through the front of the
junction box cover. Push the small gasket hole over
the mounting screw.
❒
Make sure the wire connectors and wires are inside
the junction box. Align the mounting screw with the
center hole in the mounting strap. Secure the fixture
to the mounting strap.
❒
Push the rubber plug firmly into place.
❒
If a wet location junction box was not used, caulk
the wall plate mounting surface with silicone weather
sealant.
Lamp Shade
Set Screw
Bulb Installation
NOTE:
When re-lamping,
turn power off
and let the
fixture cool.
❒
To remove lamp shade, loosen set screw 2 full
turns with a small flat-head screwdriver. Turn shade
counterclockwise and remove.
❒
To remove bulb, pull straight out of fixture.
❒
To replace bulb, push bulb pins into lamp socket.
Check that the bulb is seated properly.
❒
To reinstall lamp shade, place shade on fixture and
align notches on shade with tabs on fixture. Turn
clockwise. Tighten set screw firmly.
❒
Adjust the lamp holders by loosening the lock nuts,
but do not rotate the lamp holders more than 180°
from the factory setting.
❒
Adjust lamp shades by loosening the set screws
several turns, turn shades counterclockwise and
remove. Reinstall the shades in the desired position
and tighten set screws.
❒
Remove the existing light fixture.
❒
Install the mounting strap as shown using two screws
that fit your junction box.
❒
The plastic hanger can be used to hold the fixture
while wiring. The small end of the plastic hanger
can be threaded through the hole in the center of
the cover plate. The small end then goes into one
of the slots on the mounting strap.
❒
Route the light control’s wires through the large
gasket holes.
❒
Twist the
junction box wires and fixture wires together
as shown. Secure with wire connectors.
White
to
White
Black
to
Black
Junction box ground wire to
green ground screw on fixture.
Gasket
Mounting
Strap
Mounting
Bolt
Rubber
Plug
Wire the Light Control
WARNING: Turn power off at circuit breaker
or fuse.