Zenith SL-6053-WH User Guide - Page 3

° And 240° Motion Sensors - motion switch

Page 3 highlights

ENGLISH 180° and 240° Motion Sensors 180° Motion Sensor 240° Motion Sensor Features: • No wiring required. • Up to 70 feet sensing range, 180° or 240° Coverage (Depending upon model). • Adjustable sensitivity. • Day/Night or Night only operation. • Test mode. • DualBrite® Mode (240° Motion Sensor Only). • Uses 2 AA batteries. • Wall or eave mount. • Controls receivers up to 100 feet (30 m) away. Select Night or 24 Hour Mode These motion sensors are able to detect motion day and night or night only. To set the detection mode, remove battery compartment cover by sliding the cover down. Remove batteries if necessary. Slide the DETECT switch to either the DAY/NIGHT or NIGHT ONLY position. Replace battery compartment cover by reversing the above instructions. Installing Batteries • Before mounting motion sensor, remove battery compartment cover by sliding the cover down. Install 2 AA batteries according to polarity markings inside the battery compartment. Replace battery compartment cover by reversing the above instructions. Installing Motion Sensor 1. Install motion sensor mounting bracket where motion detection is desired. Attach motion sensor mounting bracket to a sturdy object (i.e. tree, post, house, etc.) using two screws provided. Make sure unit has an unobstructed view. Note: Attach mounting bracket vertically if connecting to a curved surface such as a post. 2. Install motion sensor to mounting bracket. Using a Philips-head screwdriver, loosen the clamp screw on the mounting bracket. Insert swivel ball mount on motion sensor into mounting bracket socket (Note: You should hear a snap). Aim motion sensor toward area where detection is desired. Tighten clamp screw. IMPORTANT: The motion sensor must be mounted with the bottom cover facing down in order to maintain water tightness. Mounting Bracket Socket Clamp Screw Swivel Ball Mount Mounting Bracket Mounting Screw Nut Sensor Installing Motion Sensor (180° Motion Sensor Shown) Detect Control DAY NIGHT NIGHT ONLY 1234 CODES DETECT CODES DETECT 1 2 3 4 DAY NIGHT NIGHT ONLY 180° Motion Sensor (Rear View) 240° Motion Sensor (Rear View) Battery Compartment 598-1306-04 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36

3
598-1306-04
ENGLISH
DETECT
CODES
1
2
3
4
DAY
NIGHT
NIGHT
ONLY
DETECT
CODES
1234
DAY
NIGHT
NIGHT
ONLY
Detect
Control
Battery Compartment
180° AND 240° MOTION SENSORS
240° Motion Sensor
180° Motion Sensor
(Rear View)
240° Motion Sensor
(Rear View)
Select Night or 24 Hour Mode
These motion sensors are able to detect motion day and night or
night only. To set the detection mode, remove battery compartment
cover by sliding the cover down. Remove batteries if necessary.
Slide the DETECT switch to either the DAY/NIGHT or NIGHT
ONLY position. Replace battery compartment cover by reversing
the above instructions.
Installing Batteries
• Before mounting motion sensor, remove battery compartment
cover by sliding the cover down.
Install 2 AA batteries according to polarity markings inside the
battery compartment. Replace battery compartment cover by
reversing the above instructions.
180° Motion Sensor
Features:
• No wiring required.
• Up to 70 feet sensing range, 180° or 240° Coverage (Depending
upon model).
• Adjustable sensitivity.
• Day/Night or Night only operation.
• Test mode.
D
UAL
B
RITE
®
Mode (240° Motion Sensor Only).
• Uses 2 AA batteries.
• Wall or eave mount.
• Controls receivers up to 100 feet (30 m) away.
Installing Motion Sensor
(180° Motion Sensor Shown)
Mounting Bracket
Clamp
Screw
Nut
Sensor
Mounting Screw
Swivel Ball Mount
Mounting
Bracket Socket
Installing Motion Sensor
1.
Install motion sensor mounting bracket where motion detection is
desired. Attach motion sensor mounting bracket to a sturdy object
(
i.e.
tree, post, house, etc.) using two screws provided. Make
sure unit has an unobstructed view.
Note:
Attach mounting
bracket vertically if connecting to a curved surface such as a
post.
2.
Install motion sensor to mounting bracket. Using a Philips-head
screwdriver, loosen the clamp screw on the mounting bracket.
Insert swivel ball mount on motion sensor into mounting bracket
socket (
Note:
You should hear a snap). Aim motion sensor toward
area where detection is desired. Tighten clamp screw.
IMPORTANT:
The motion sensor must be mounted with the bottom
cover facing down in order to maintain water tightness.