2006 BMW X3 Owner's Manual - Page 68

2006 BMW X3 Manual

Get 2006 BMW X3 PDF manuals and user guides View all 2006 BMW X3 manuals

Page 68 highlights

Practical interior accessories The corresponding memory button 1 is now programmed with the signal of the original hand-held transmitter. You can use the system when the engine is running or when the ignition is switched on. If the system cannot be operated after repeated programming, check whether the original hand-held transmitter uses an alternating-code system. To do so, either read the instructions of the original hand-held transmitter or press and hold down the programmed memory button 1 of the integrated universal remote control. If the LED 2 on the integrated universal remote control flashes rapidly for a short time then lights up for approx. 2 seconds, this indicates that the original hand-held transmitter uses an alternating-code system. In the case of an alternating-code system, program the memory buttons 1 as described in the section below on alternating-code transmitters.< The corresponding memory button 1 is now programmed with the signal of the original hand-held transmitter. If you have questions, please contact your BMW Sports Activity Vehicle Center.< Deleting stored programs Press both outer buttons 1 for approx. 20 seconds, maintaining pressure until the LED 2 starts to flash: all stored programs are deleted. It is not possible to delete individual programs. Cup holders Do not place glass containers in the cup holders; otherwise, there is a danger of injury in the event of an accident.< Front Alternating-code transmitters Consult the operating instructions of the unit you wish to set when programming the universal remote control. You will find information there on the possibilities for synchronization. When programming hand-held transmitters that employ an alternating code, please follow these additional instructions: Programming will be easier with the aid of a second person.< 1. Park your vehicle within the range of the remote-controlled equipment. 2. Program the integrated universal remote control as described above in the section on Fixed-code hand-held transmitters. 3. Locate the button on the receiver of the equipment to be set, e.g. on its drive unit. 4. Press the button on the receiver of the device you want to set up. After step 4, you have approx. 30 seconds for step 5. 5. Press the programmed memory button 1 of the integrated universal remote control three times. Depending on your optional equipment, the center console contains either one or two cup holders. Passenger side* The cup holder for the front passenger is located beneath the air vent. 66 Online Edition for Part No. 01 41 0 012 213 - © 02/06 BMW AG

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
Practical interior accessories
66
The corresponding memory button
1
is now
programmed with the signal of the original
hand-held transmitter.
You can use the system when the engine is run-
ning or when the ignition is switched on.
If the system cannot be operated after
repeated programming, check whether
the original hand-held transmitter uses an alter-
nating-code system. To do so, either read the
instructions of the original hand-held transmit-
ter or press and hold down the programmed
memory button
1
of the integrated universal
remote control. If the LED
2
on the integrated
universal remote control flashes rapidly for a
short time then lights up for approx. 2 seconds,
this indicates that the original hand-held trans-
mitter uses an alternating-code system. In the
case of an alternating-code system, program
the memory buttons
1
as described in the sec-
tion below on alternating-code transmitters.
<
Alternating-code transmitters
Consult the operating instructions of the unit
you wish to set when programming the univer-
sal remote control. You will find information
there on the possibilities for synchronization.
When programming hand-held transmitters
that employ an alternating code, please follow
these additional instructions:
Programming will be easier with the aid of
a second person.
<
1.
Park your vehicle within the range of the
remote-controlled equipment.
2.
Program the integrated universal remote
control as described above in the section on
Fixed-code hand-held transmitters.
3.
Locate the button on the receiver of the
equipment to be set, e.g. on its drive unit.
4.
Press the button on the receiver of the
device you want to set up. After step 4, you
have approx. 30 seconds for step 5.
5.
Press the programmed memory button
1
of the integrated universal remote control
three times.
The corresponding memory button
1
is now
programmed with the signal of the original
hand-held transmitter.
If you have questions, please contact your
BMW Sports Activity Vehicle Center.
<
Deleting stored programs
Press both outer buttons
1
for approx. 20 sec-
onds, maintaining pressure until the LED
2
starts to flash: all stored programs are deleted.
It is not possible to delete individual programs.
Cup holders
Do not place glass containers in the cup
holders; otherwise, there is a danger of
injury in the event of an accident.
<
Front
Depending on your optional equipment, the
center console contains either one or two cup
holders.
Passenger side*
The cup holder for the front passenger is
located beneath the air vent.