2006 Polaris 120 Owners Manual - Page 81

2006 Polaris 120 Manual

Get 2006 Polaris 120 PDF manuals and user guides View all 2006 Polaris 120 manuals

Page 81 highlights

ADULT SECTION Maintenance Ski Skags The skag (A) is a replaceable bar attached to the underside of the ski. The purpose of the skag is to assist in turning the snowmobile and to prevent the wearing away of the ski caused by contact with roads and other bare terrain. We A recommend that skags be checked once a week to maintain positive steering characteristics. Skags must be replaced when worn to half their original diameter. NOTE: See dealer track studding and skag chart for recommended skags. WARNING Worn skis and/or skags will adversely affect handling and can cause loss of vehicle control, which can lead to serious injury or death. Replace worn skis and/or skags when inspection reveals wear. Skag Replacement 1. Raise and support the front of the machine so the skis are approximately 6″ (15.2 cm) from the ground. 2. Remove the attaching nuts and pry the skag downward. 3. Remove the forward portion of the skag. Reverse this procedure for new skag installation. NOTE: If the rear idler wheel assembly (1) washers are removed, be sure they are reinstalled with the domed side of the washer facing out (2) as shown. 1 2 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
78
ADULT SECTION
Maintenance
Ski Skags
The skag (A) is a replaceable bar
attached to the underside of
the ski. The purpose of the
skag is to assist in turning
the snowmobile and to
prevent the wearing away of the
ski caused by contact with roads
and other bare terrain. We
recommend that skags be checked
once a week to maintain positive
steering characteristics. Skags must be replaced when worn to half
their original diameter.
NOTE:
See dealer track studding and skag chart for recommended
skags.
WARNING
Worn skis and/or skags will adversely affect handling and can
cause loss of vehicle control, which can lead to serious injury or
death. Replace worn skis and/or skags when inspection reveals
wear.
Skag Replacement
1.
Raise and support the front of the machine so the skis are
approximately 6
″
(15.2 cm) from the ground.
2.
Remove the attaching nuts and pry the skag downward.
3.
Remove the forward portion of the skag.
Reverse this procedure for new skag installation.
NOTE:
I
f the rear idler wheel
assembly (1) washers
are removed, be sure
they are reinstalled with
the domed side of the
washer facing out (2) as
shown.
A
2
1