2004 Volvo S40 Owner's Manual - Page 46

2004 Volvo S40 Manual

Get 2004 Volvo S40 PDF manuals and user guides View all 2004 Volvo S40 manuals

Page 46 highlights

Install the wheel lugs and tighten handtight. Using the lug wrench. Tighten crosswise until all lugs are snug. Lower the vehicle to the ground and alternately tighten the lugs crosswise to 81 ft. lbs. (110 Nm). Install the wheel cover (where applicable). CAUTION: Correct tightening torque on wheel lugs must be observed. The wheel lugs should never be greased or lubricated. Extended, chromed wheel lugs must not be used with steel rims, as they make it impossible to fit the hub caps. pg. 89 Replacing bulbs Removing high/low beam headlight bulbs Your car is fitted with separate high and low beam bulbs. Switch off the lights and remove the ignition key. Open the hood. Pull off the rubber cover from the rear of the bulb unit to be replaced. Release the retaining spring and withdraw the connector/bulb from the headlight unit. Pull the bulb out of the connector. NOTE: Never touch the glass of a bulb with your fingers: this could leave traces of grease or oil on the glass which then evaporate and may damage the reflector. pg. 90 Replacing bulbs

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
Install the wheel lugs and tighten handtight.
Using the lug wrench. Tighten crosswise until all lugs are snug.
Lower the vehicle to the ground and alternately tighten the lugs crosswise to 81 ft. lbs. (110 Nm).
Install the wheel cover (where applicable).
CAUTION:
Correct tightening torque on wheel lugs must be observed. The wheel lugs should never be greased or lubricated.
Extended, chromed wheel lugs must not be used with steel rims, as they make it impossible to fit the hub caps.
pg. 89 Replacing bulbs
Removing high/low beam headlight bulbs
Your car is fitted with separate high and low beam bulbs.
Switch off the lights and remove the ignition key.
Open the hood.
Pull off the rubber cover from the rear of the bulb unit to be replaced.
Release the retaining spring and withdraw the connector/bulb from the headlight unit. Pull the bulb out of the
connector.
NOTE: Never touch the glass
of a bulb with your fingers: this could leave traces of grease or oil on the glass which
then evaporate and may damage the reflector.
pg. 90 Replacing bulbs