3Com 3C17700 Getting Started Guide - Page 20

Console Port, Expansion Module Slot, Default Settings - features

Get 3Com 3C17700 - SuperStack 3 Switch 4900 PDF manuals and user guides
UPC - 662705357720
View all 3Com 3C17700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

20 CHAPTER 1: INTRODUCING THE SUPERSTACK 3 SWITCH 4900 FAMILY Console Port The console port allows you to connect a terminal and perform remote or local out-of-band management. The console port uses a standard null modem cable and is set to auto-baud (up to a maximum of 19200 baud), 8 data bits, no parity and 1 stop bit. Expansion Module You can use this slot to install an Expansion Module. Contact your Slot supplier for further information on the range of Expansion Modules supported by your Switch. WARNING: When an Expansion Module is not installed, ensure the blanking plate is fitted by tightening all screws with a suitable tool. Default Settings Table 5 shows the default settings for the Switches. If you initialize one of the Switch units, it is returned to these defaults. Table 5 Default Setting Feature Port Status Port Speed Duplex Mode Flow Control Broadcast Storm Control Virtual LANs (VLANs) Multicast Filtering Rapid Spanning Tree Protocol Link Aggregation Control Protocol (LACP) Smart Auto-sensing IP Address Subnet Mask Switch 4900 Family Enabled Auto-negotiated Auto-negotiated Auto-negotiated Enabled High threshold: 3000 broadcast frames per second - Notify and filter Low threshold: 1500 broadcast frames per second - Notify and unfilter All ports belong to the untagged Default VLAN (VLAN 1) IGMP filtering enabled Enabled Disabled per port Switch 4900, 4924, and 4950: Enabled Switch 4900 SX: Not applicable 169.254.100.100* 255.255.0.0 * This default IP address is used if the unit is operating in standalone mode, and/or no other Switches on the network have this IP address. If this default IP address is already in use then the Switch detects this and configures itself with an IP address in the range 169.254.1.0 to 169.254.254.255.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
20
C
HAPTER
1: I
NTRODUCING
THE
S
UPER
S
TACK
3 S
WITCH
4900 F
AMILY
Console Port
The console port allows you to connect a terminal and perform remote or
local out-of-band management. The console port uses a standard null
modem cable and is set to auto-baud (up to a maximum of 19200 baud),
8 data bits, no parity and 1 stop bit.
Expansion Module
Slot
You can use this slot to install an Expansion Module. Contact your
supplier for further information on the range of Expansion Modules
supported by your Switch.
WARNING:
When an Expansion Module is not installed, ensure the
blanking plate is fitted by tightening all screws with a suitable tool.
Default Settings
Table 5
shows the default settings for the Switches. If you initialize one of
the Switch units, it is returned to these defaults.
Table 5
Default Setting
Feature
Switch 4900 Family
Port Status
Enabled
Port Speed
Auto-negotiated
Duplex Mode
Auto-negotiated
Flow Control
Auto-negotiated
Broadcast Storm Control
Enabled
High threshold: 3000 broadcast frames per
second — Notify and filter
Low threshold: 1500 broadcast frames per
second — Notify and unfilter
Virtual LANs (VLANs)
All ports belong to the untagged Default VLAN
(VLAN 1)
Multicast Filtering
IGMP filtering enabled
Rapid Spanning Tree Protocol
Enabled
Link Aggregation Control
Protocol (LACP)
Disabled per port
Smart Auto-sensing
Switch 4900, 4924, and 4950:
Enabled
Switch 4900 SX
: Not applicable
IP Address
169.254.100.100
*
* This default IP address is used if the unit is operating in standalone mode, and/or no other
Switches on the network have this IP address. If this default IP address is already in use then the
Switch detects this and configures itself with an IP address in the range 169.254.1.0 to
169.254.254.255.
Subnet Mask
255.255.0.0