3M X62 User Manual - Page 5

About Restart switch, please push the Restart switch by using a cocktail stick or similar, and before - - digital projector

Get 3M X62 PDF manuals and user guides View all 3M X62 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

3M™ Digital Projector X62 Ports (See below.) Rear-Left side Part names Power switch ( 17) AC inlet ( 14) Elevator button ( 9) Elevator foot ( 9) Vent ( 7) AUDIO IN1 port ( 12) (In the default setting, the AUDIO IN1 port is the audio AUDIO IN3 L/R port ( 13) (In the default setting, the port for the RGB IN1 port, however, it is possible to change the settings. 36) AUDIO IN3 L/R port is the audio port for the VIDEO, S-VIDEO RGB IN1 port ( 12) and COMPONENT VIDEO ports, however it is possible to Restart switch (*) ( 58) change the settings. 36) RGB IN2 port ( 12) COMPONENT VIDEO ports ( 13) Y CB/PB CR/PR VIDEO port ( 13) AUDIO IN3 Y R CB/PB L CR/PR VIDEO S-VIDEO RGB IN1 AUDIO IN1 AUDIO IN2 K RGB OUT port ( 12) RGB IN2 RGB OUT AUDIO OUT AUDIO OUT port ( 12) CONTROL USB Ports S-VIDEO port ( 13) USB port ( 12) AUDIO IN2 port ( 12) (In the default setting, the AUDIO CONTROL port ( 12) IN2 port is the audio port for the RGB IN2 port, however, it is Kensington lock slot possible to change the settings. 36) NOTE (*) About Restart switch: This projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly and the microprocessor will need to be reset. In such a case, please push the Restart switch by using a cocktail stick or similar, and before turning on again, make the projector cool down at least 10 minutes without operating. Only push the Restart switch in these exceptional instances. © 3M 2006. All Rights Reserved. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
5
Y
R
L
AUDIO IN3
AUDIO IN1
AUDIO OUT
USB
RGB OUT
AUDIO IN2
VIDEO
S-VIDEO
C
B
/
P
B
C
R
/
P
R
CONTROL
RGB IN2
RGB IN1
K
AC inlet (
14
)
Power switch (
17
)
Elevator button (
9
)
COMPONENT
VIDEO ports (
13
)
Y
C
B
/P
B
C
R
/P
R
S-VIDEO port (
13
)
VIDEO port (
13
)
CONTROL port (
12)
Elevator foot (
9
)
Rear-Left side
Ports (See below.)
Vent (
7
)
AUDIO OUT port
(
12
)
Ports
AUDIO IN2 port (
12
)
(In the default setting, the AUDIO
IN2 port is the audio port for
the RGB IN2 port, however, it is
possible to change the settings.
36
)
AUDIO IN3 L/R port (
13
)
(In the default setting, the
AUDIO IN3 L/R port is the audio
port for the VIDEO, S-VIDEO
and COMPONENT VIDEO
ports, however it is possible to
change the settings.
36
)
RGB IN2 port (
12
)
NOTE
(*) About Restart switch:
This projector is controlled by an internal
microprocessor. Under certain exceptional circumstances, the projector may not
operate correctly and the microprocessor will need to be reset. In such a case,
please push the Restart switch by using a cocktail stick or similar, and before
turning on again, make the projector cool down at least 10 minutes without
operating. Only push the Restart switch in these exceptional instances.
Restart switch (*) (
58
)
Part names
USB port (
12
)
Kensington lock slot
RGB OUT port (
12
)
RGB IN1 port (
12
)
AUDIO IN1 port (
12
)
(In the default setting, the AUDIO IN1 port is the audio
port for the RGB IN1 port, however, it is possible to
change the settings.
36
)
3M™ Digital Projector X62
© 3M 2006.
All Rights Reserved.