AEG IKB64301XB User Manual - Page 17

Installation

Get AEG IKB64301XB PDF manuals and user guides View all AEG IKB64301XB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

ENGLISH 17 Problem and a number come on. You can hear a constant beep noise. Possible cause There is an error in the hob. The electrical connection is incorrect. Remedy Deactivate the hob and activate it again after 30 sec- onds. If comes on again, disconnect the hob from the electrical supply. After 30 seconds, connect the hob again. If the problem continues, speak to an Authorised Service Centre. Disconnect the hob from the electrical supply. Ask a qualified electrician to check the installation. 7.2 If you cannot find a solution... If you cannot find a solution to the problem yourself, contact your dealer or an Authorised Service Centre. Give the data from the rating plate. Give also three digit letter code for the glass ceramic (it is in the corner of the glass 8. INSTALLATION surface) and an error message that comes on. Make sure, you operated the hob correctly. If not the servicing by a service technician or dealer will not be free of charge, also during the warranty period. The instructions about the Service Centre and conditions of guarantee are in the guarantee booklet. WARNING! Refer to Safety chapters. 8.1 Before the installation Before you install the hob, write down the information bellow from the rating plate. The rating plate is on the bottom of the hob. Serial number 8.2 Built-in hobs Only use the built-in hobs after you assemble the hob into correct built-in units and work surfaces that align to the standards. 8.3 Connection cable • For a single phase or two phase connection, use the cable type: H05BB-F or H03V2V2-F which withstands a temperature of 70°C or higher. • To replace the damaged mains cable, use the cable: H05BB-F or H03V2V2-F which withstands a temperature of 70°C or higher.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Problem
Possible cause
Remedy
and a number come on.
There is an error in the hob.
Deactivate the hob and acti-
vate it again after 30 sec-
onds. If
comes on again,
disconnect the hob from the
electrical supply. After 30
seconds, connect the hob
again. If the problem contin-
ues, speak to an Authorised
Service Centre.
You can hear a constant
beep noise.
The electrical connection is
incorrect.
Disconnect the hob from the
electrical supply. Ask a quali-
fied electrician to check the
installation.
7.2
If you cannot find a
solution...
If you cannot find a solution to the
problem yourself, contact your dealer or
an Authorised Service Centre. Give the
data from the rating plate. Give also
three digit letter code for the glass
ceramic (it is in the corner of the glass
surface) and an error message that
comes on. Make sure, you operated the
hob correctly. If not the servicing by a
service technician or dealer will not be
free of charge, also during the warranty
period. The instructions about the
Service Centre and conditions of
guarantee are in the guarantee booklet.
8.
INSTALLATION
WARNING!
Refer to Safety chapters.
8.1
Before the installation
Before you install the hob, write down
the information bellow from the rating
plate. The rating plate is on the bottom
of the hob.
Serial number
...........................
8.2
Built-in hobs
Only use the built-in hobs after you
assemble the hob into correct built-in
units and work surfaces that align to the
standards.
8.3
Connection cable
•
For a single phase or two phase
connection, use the cable type:
H05BB-F or H03V2V2-F which
withstands a temperature of 70°C or
higher.
•
To replace the damaged mains cable,
use the cable: H05BB-F or H03V2V2-F
which withstands a temperature of
70°C or higher.
ENGLISH
17